SentrySafe SFW205URC Manual De Propietario página 2

Water/Fire Resistant Alarm Safe
Thank you for choosing SentrySafe to store all your important documents and valuables.
We hope that this product will help you stay organized and provide you with the peace-of-mind of knowing the things most important to you are protected.
Your SentrySafe Product
Your SentrySafe product has a number of features to keep your
important documents and valuables protected including:
Water Protection UL Classified
Fire Protection
Loud Audible Alarm
THE LOUD AUDIBLE ALARM ALERTS YOU WHEN:
The safe is picked up
or moved
There is an attempt
to pry the door open
The wrong combination
is entered 5 times
The safe is jolted,
hit or jarred
Using Your SentrySafe
Alarm Safe
Preparing Your Safe for First Time Use
1
Remove lock out screw indicated by the
yellow tag on the inside of the door
of the safe.
2
Remove battery compartment from
Digital Media
inside door and insert 4 AAA alkaline
Protection
batteries. DO NOT use rechargeable
batteries or any other type of non-
alkaline battery. Do not mix old and
new batteries. Do not mix alkaline and
standard batteries.
3
Replace battery compartment.
Using Your Safe
Touch the keypad to wake up the safe.
1
2 Enter the 5 digit factory code found on
the back of this owner's manual.
3 Turn handle to open safe.
IMPORTANT: Test your code several times before putting
valuables inside.
IMPORTANT: A dual key lock option may be included
in your safe. Using this key can disable/enable entry into
the safe.
IMPORTANT: If you exert too much force on the handle,
the handle will move without moving the bolts. When this
happens, you will hear a 'click.' DO NOT be alarmed.
This feature is designed to protect the bolts from being
over powered by force. Simply exert force in the opposite
direction (lifting up) until the handle clicks back
into place.
IMPORTANT: Like a home alarm system, the alarm must
be set each time you lock your safe to activate the
audible alert. In the event your alarm is not activated
and 5 wrong code attempts are entered, the safe will
go into delay mode for 2 minutes. No alarm will go off
when moved, jarred or with attempted forced entry.
1
Close and lock the door of your safe.
2
Touch the keypad to wake up the safe.
3
Press: "0" – "PROG" – "9"
The alarm indicator will blink every
10 seconds to indicate the alarm has
been activated.
Setting the Alarm
Programmable Codes
Your SentrySafe comes with 3 types of codes for accessing
your safe. For more information on programming these codes
see the "Programming Safe Features" section of this
owner's manual.
FACTORY CODE (FC): The safe will ALWAYS unlock using this 5
digit code (found on the back of this owner's manual). This code
cannot be deleted or changed.
USER CODE (UC): A 5 digit programmable code of your choosing
that can be changed or deleted.
SECONDARY CODE (SC): A 5 digit programmable code of your
choosing that can be changed or deleted. Can only be
programmed after a user code has been activated.
Audible Alarm
Features
Turning off the Alarm
If the loud audible alarm on your safe has been triggered:
1
Touch the keypad to wake up the safe.
2 Enter a valid code.
NOTE: You will need to enter your code again to open the safe.
NOTE: The Factory Code (FC) or User Code (UC) must be
entered to program safe settings. A secondary code cannot
be used.
Changing Alarm Sensitivity
You can change the level of sensitivity on your safe alarm from a scale
of zero "0" to "5". Zero "0" being the least sensitive only responding
to incorrect codes and "5" being the most sensitive to slight
movement of the safe.
1
Touch the keypad to wake up the safe.
2 Press: "0" – "PROG" – "PROG" – "(FC)" OR "(UC)" – "3"
3 Then press "0", "1", "2", "3", "4" OR "5" to program your
desired sensitivity.
Changing Length of Alarm
You may also change the length of which your alarm will sound once
triggered from 01 to 99 minutes.
1
Touch the keypad to wake up the safe.
2
Press: "0" – "PROG" – "PROG" – "(FC)" OR "(UC)" – "4"
3 Then press any number between 01 and 99 to indicate the
number of minutes you would like your alarm to sound
once triggered.