cecotec BOLERO COOLMARKET COMBI 356 WHITE D Manual De Instrucciones página 30

ENGLISH
3. INSTALLATION
Place of installation
Ventilation condition
The location you choose for the installation of the refrigerator must be properly ventilated and
away from heat sources. Do not place the refrigerator near heat sources, like a cooker or pot,
and avoid direct sunlight to ensure the cooling effect and save on energy consumption. Do not
place the refrigerator in a damp place to avoid rust or loss of power. The result of dividing the
total space of the room in which the refrigerator is installed by the amount of refrigerant load
in the refrigerator must not be less than 8 g/m³.
Note:
The amount of refrigerant used by the refrigerator is specified on the rating plate.
Heat dissipation space
During operation, the refrigerator releases heat into the environment. Therefore, you should
leave at least 30 mm of free space at the top chamber, more than 100 mm on both sides, and
more than 50 mm at the rear of the refrigerator. Fig. 2
W (mm) D (mm) H (mm) A (mm)
595 635 2000 966
Note:
Figure 2 only illustrates the space required for the appliance.
Stable surface
Place the refrigerator on a solid, flat surface (the floor) to keep it stable, otherwise vibrations
and noises will occur. When the refrigerator is placed on a carpet, straw mat, or polyvinyl
chloride, solid support plates should be placed under the refrigerator to avoid colour change
due to heat dissipation.
Preparing for use
Waiting time
Once the refrigerator is properly installed and cleaned, do not switch it on immediately. Be
sure to wait at least one hour before switching the refrigerator on to ensure normal operation.
Cleaning
Check the placement of the interior accessory parts and clean the inside of the refrigerator
with a soft cloth.
B O LE R O COOLM ARKET COM BI 3 56 WHIT E D/INOX D/
58
DA R K D/W HI TE GLASS D/ BLAC K GL ASS D/ GLA SS GRE Y D
B (mm) C (°) E (mm) F (mm)
1202 130 50 100
Switch-on
Connect the plug into a power socket to switch on the compressor. After one hour, open the
freezer door: if the temperature inside the freezer compartment has dropped, the cooling
system is running normally.
Food storage
- After the refrigerator has been in operation for some time, the user may adjust its internal
temperature. Once the refrigerator has reached a suitable interior temperature, put
in the food. These will take 2 to 3 hours to cool down completely. In summer, when the
temperature is high, it may take more than 4 hours for food to cool down completely (try to
open the refrigerator door as rarely as possible).
- If the refrigerator is installed in a wet place, be sure to check if the earth wire and the
leakage circuit breaker are working normally. If vibration noises occur due to contact of
the refrigerator with the wall or if the wall turns black due to air convection around the
compressor, keep the refrigerator further away from the wall. The installation of the
refrigerator may cause noise interference or image problems in mobile phones, landline
phones, radio receivers, or TVs near the appliance, so in this case, keep the latter as far
away from these objects as possible.
Changing the opening direction of the door
If desired, you can change the direction in which the door opens, from the right side (by default)
to the left side.
Warnings:
- The refrigerator must not be connected to the power socket when you change the opening
direction of the door. Make sure to disconnect the plug from the power socket.
- Check figure 5 to check the tools you need.
- It is advisable that two people change the opening direction of the door.
Fig. 5
A. Tools not supplied
8-mm tube wrench
1.
2. Flat-head screwdriver
3. Spatula
4. Crosshead screwdriver
Spanner
5.
6. 8-mm wrench
B. Additional parts (included in the plastic bag)
Upper-left hinge
7.
8. Upper-left hinge cover
BOLERO COOLMARKET COMBI 3 56 W HITE D/IN OX D/
DA RK D/WHITE G LA SS D/BLACK G LASS D/ G LA SS
ENGLISH
59
G REY D