Tesmed Trio 6.5 Manual De Instrucciones página 165

The 【 【 FDES116 】 】 is intended for use in the electromagnetic environment specified below. The customer or the
user of 【 【 FDES116 】 】 should assure that it is used in such an environment.
Emissions test Compliance
Guidance and manufacturer´s declaration – electromagnetic emission –
RF emissions
Guidance and manufacturer´s declaration – electromagnetic emission
Group 1
The 【 【 FDES116 】 】 is intended for use in the electromagnetic environment specified below. The customer or the
CISPR 11
user of 【 【 FDES116 】 】 should assure that it is used in such an environment.
RF emissions Emissions test Compliance
CISPR 11
RF emissions
Harmonic emissions
Group 1
CISPR 11
IEC 61000-3-2
RF emissions
CISPR 11
Voltage fluctuations
Harmonic emissions
flicker emissions
Complies
IEC 61000-3-3
IEC 61000-3-2
Voltage fluctuations
flicker emissions
Complies
IEC 61000-3-3
Guidance and manufacturer's declaration – electromagnetic immunity –
Guidance and manufacturer´s declaration – electromagnetic immunity
The 【 【 FDES116 】 】 is intended for use in the electromagnetic environment specified below. The customer or the user of
the 【 【 FDES116 】 】 should assure that it is used in such an environment.
Guidance and manufacturer's declaration – electromagnetic immunity –
IEC 60601
Immunity test
test level
Guidance and manufacturer´s declaration – electromagnetic immunity
Electrostatic ± 8 kV contact
discharge (ESD)
The 【 【 FDES116 】 】 is intended for use in the electromagnetic environment specified below. The customer or the user of
± 2 kV, ± 4 kV, ± 8 kV,
the 【 【 FDES116 】 】 should assure that it is used in such an environment.
IEC 61000-4-2 ± 15 kV air
IEC 60601
Immunity test
test level
Electrostatic ± 8 kV contact
± 2 kV for power
discharge (ESD)
Electrostatic
supply lines
± 2 kV, ± 4 kV, ± 8 kV,
transient / burst
IEC 61000-4-2 ± 15 kV air
± 1 kV for input/output
IEC 61000-4-4
lines
± 2 kV for power
Electrostatic
supply lines
transient / burst
± 1 kV differential
Surge
mode
± 1 kV for input/output
IEC 61000-4-4
lines
IEC 61000-4-5
± 2 kV common mode
± 1 kV differential
Surge
mode
IEC 61000-4-5
0 % UT; 0,5 cycle g) At
± 2 kV common mode
Voltage dips, short 0°, 45°, 90°, 135°, 180°,
interruptions and 225°, 270° and 315°
voltage variations
on power supply 0 % UT; 1 cycle and
input lines 70 % UT; 25/30 cycles
Single phase: at 0°
IEC 61000-4-11
0 % UT; 250/300 cycle
Power frequency
(50/60 Hz)
magnetic field 30 A/m
IEC 61000-4-8
NOTE U is the a. c. mains voltage prior to application of the test level.
T
Tesmed copyright - it is absolutely forbidden the partial or total reproduction of any present content
Electromagnetic environment - guidance
for all EQUIPMENT AND SYSTEMS
The 【 【 FDES116 】 】 uses RF energy only for its internal function.
There for, its RF emissions are very low and are not likely to cause
any interference in nearby electronic equipment.
Electromagnetic environment - guidance
Class B
The 【 【 FDES116 】 】 suitable for use in all establishments,
The 【 【 FDES116 】 】 uses RF energy only for its internal function.
including domestic establishments and those directly connected to
There for, its RF emissions are very low and are not likely to cause
the public low-voltage power supply network that supplies
any interference in nearby electronic equipment.
Class A
buildings used for domestic purposes.
Class B
The 【 【 FDES116 】 】 suitable for use in all establishments,
including domestic establishments and those directly connected to
the public low-voltage power supply network that supplies
Class A
buildings used for domestic purposes.
for all EQUIPMENT and SYSTEMS
for all EQUIPMENT and SYSTEMS
Compliance level
± 8 kV contact
± 2 kV, ± 4 kV, ± 8 kV,
± 15 kV air
Compliance level
± 8 kV contact
± 2 kV for power
± 2 kV, ± 4 kV, ± 8 kV,
supply lines
± 15 kV air
± 2 kV for power
supply lines
± 1 kV differential mode
± 1 kV differential mode
0 % UT; 0,5 cycle g) At 0°,
45°, 90°, 135°, 180°, 225°,
270° and 315°
0 % UT; 1 cycle and 70 % UT;
25/30 cycles Single phase: at
0°
0 % UT; 250/300 cycle
30 A/m
165
Electromagnetic environment -
guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30 %.
Electromagnetic environment -
guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered with
Mains power quality should be that of a
synthetic material, the relative humidity
typical commercial or hospital
should be at least 30 %.
environment.
Mains power quality should be that of a
typical commercial or hospital
Mains power quality should be that of a
environment.
typical commercial or hospital
environment.
Mains power quality should be that of a
typical commercial or hospital
Mains power quality should be that of a environment.
typical commercial or hospital
environment. If the user of the
【 【 FDES116 】 】 requires continued
operation during power mains
interruptions, it is recommended that the
【 【 FDES116 】 】 be powered from an
uninterruptible power supply or a
battery.
Power frequency magnetic fields should
be at levels characteristic of a typical
location in a typical commercial or
hospital environment.