Publicidad
Idiomas disponibles
Idiomas disponibles
Clearance To Combustibles
Keep electrical cords, drapery, furniture and other
combustibles at least 3 feet (.914 M) from the front of the
heater and away from the sides and top.
Clearance To Combustibles
Front
Top
Sides
Electrical Connection
A 15 AMP, 120 Volt, 60 Hz circuit with a properly grounded
outlet is required. Preferably, the heater will be on a
dedicated circuit as other appliances on the same circuit
may cause the circuit breaker to trip or the fuse to blow
when the heater is in operation.
CAUTION: Do not exceed the current rating of the
current tap. Always plug heaters directly into a wall outlet/
receptacle. Never use with an extension cord or relocatable
power tap (outlet/power strip).
Grounding Instructions
This heater is for use on 120 volts. The cord has a plug
as shown as A in Figure 1. An adapter as shown as C
is available (sold separately) for connecting three-blade
grounding-type plugs to two-slot receptacles. The green
grounding lug extending from the adapter must be
connected to a permanent ground such as a properly
grounded outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
Grounding
Pin
Adapter
Grounding
Lug
Remote Control
This remote control uses one CR2025 battery (included).
Instructions for battery installation are on the Remote
Control battery compartment. Refer to Figure 2 for battery
removal procedure.
Figure 2
WARNING: Chemical Burn Hazard. Keep batteries
away from children.
Wall Mounted Forced Air Electric Heater
3'
3'
3'
Metal Screw
Cover of Grounded
Outlet Box
Grounding
Pin
Figure 1
This product contains a lithium button/coin cell battery. If a new
or used lithium button/coin cell battery is swallowed or enters
the body, it can cause severe internal burns and can lead to
death in as little as 2 hours. Always completely secure the battery
compartment. If the battery compartment does not close securely,
stop using the product, remove the batteries, and keep it away
from children. If you think batteries might have been swallowed
or placed inside any part of the body, seek immediate medical
attention.
Heater Location
When choosing a location for your new heater, ensure that
the general instructions are followed. For best effect, install
the heater out of direct sunlight.
To prevent fire there must be a minimum clearance of 50
cm (20 inches) on the sides and bottom and 100 cm (40
inches) on the top of the unit.
Cold climate installation recommendation: when installing
this unit against a non-insulated exterior wall, it is
mandatory that the outer walls be insulated to conform
to applicable insulation codes. If you choose to place
the unit underneath a window or on a poorly insulated
exterior wall, please be advised that the heater may read a
colder ambient temperature then the actual ambient
temperature of the room.
Wall Mounting Assembly
WARNING: Your heater MUST BE installed on a
wall. Do not prop the heater up against objects or
use the heater with the grill placed vertically.
PRIOR TO MOUNTING: When drilling holes in this
area check the wall to ensure there are no wires,
pipes, etc.
A SOLID WALL must be used for mounting this
unit. Unit CANNOT be mounted on a hollow wall,
or wall without studs.
1.
Carefully place the heater on its backside on a
protected surface. Attach the L-shaped brackets onto
the bottom of the unit using two M5 x 16mm screws.
2. Choose a location near an outlet so an extension cord
is not required. Do not position the heater directly
below a power outlet. The unit cannot be mounted
near electrical cables, communication lines, pipes,
combustible materials, etc. that could be damaged or
ignited by excessive heat.
3. Predrill two holes in the wall 262mm apart (make sure
they are horizontal ). Insert two wall anchors and two
ST4 x 28mm screws.
4. Hang the heater by sliding the it onto the screws using
the two keyslots at back of unit.
5. Using the two holes in the L-shaped brackets, predrill
two holes in the wall for the other two anchors and
ST4 x 28mm screws. Insert the anchors into these holes
and screw in the two screws to finish securing the
heater to the wall.
L-Brackets (w/M5x16mm screws)
Bottom
View
ST4 x 28mm Screws w/anchors (not shown)
4
Installation Instructions and Owner's Manual
(Refer to Figure 3)
Figure 3
Publicidad
