Hatco HW Serie Manual De Instalación Y Operación página 9

General
Countertop Heated Wells are designed for maximum durability
and performance, with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not clean unit when it is energized or hot.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Do not use flammable cleaning solutions
to clean this unit.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
+1-414-671-6350.
BURN HAZARD: Hot water in unit may cause scalding
injury. Allow unit to cool before draining or cleaning.
Do not move or relocate unit when it contains food
product. Turn off unit, remove food product, and allow to
cool completely before moving or cleaning.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Do not use steel wool for cleaning. Steel wool will scratch
the finish.
Do not use harsh chemicals such as bleach, cleaners
containing bleach, or oven cleaners to clean this unit.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
HWCEM-1023
CAUTION
Daily Cleaning
To preserve the finish of the heated well, perform the following
cleaning procedure daily.
1. Move the Power I/O Switch (on/off) to the O (off) position,
unplug the power cord, and allow the unit to cool.
2. Remove and wash any pans and adapters.
3. Remove water from the well if used for wet operation.
4. Wipe down the entire unit using a clean cloth or sponge
and mild detergent.
5. Use a plastic scouring pad to remove any hardened food
particles or mineral deposits.
6. Wipe the well thoroughly with a clean, damp cloth to remove
all detergent residue. Rinse cloth and repeat, if necessary.
7. Wipe dry the entire unit using a non-abrasive, dry cloth.
Removing Lime and Mineral Deposits
Use the following procedure for periodic cleaning and deliming
of the heated well.
NOTE: The lime and mineral content of the water used for
daily operation will determine how often the deliming
procedure must be performed.
NOTE: Perform this procedure when the unit will not be used
for a period of time, such as the end of the day.
1. Move the Power I/O Switch (on/off) to the O (off) position,
unplug the power cord, and allow the unit to cool.
2. Remove and wash any pans and adapters.
3. Remove water from the well if used for wet operation.
4. Add a mixture of 50% water
and 50% white vinegar to
the well until solution is
at normal operating level
("MAX" fill line) or covers
the accumulated scale. Do
not use flavored vinegar.
5. Plug in and turn on the unit.
6. Turn the Temperature
Control fully clockwise to
the HIGH position. Allow the unit to run for 30 minutes.
7. Move the Power I/O Switch (on/off) to the O (off) position,
unplug the power cord, and cover the well.
8. Allow the solution to soak for at least one hour or overnight
for heavy buildup.
9. Remove the water/cleaning solution from the well.
10. Scrub the well with a plastic scouring pad.
11. Wipe the well thoroughly with a clean, damp cloth to remove
all residue. Rinse cloth and repeat, if necessary.
12. Wipe dry the entire unit using a non-abrasive, dry cloth.
NOTE: Heavy scale buildup may require additional treatments.
9
MAINTENANCE
"MAX"
Fill Line