cecotec HIDROBOOST 1600 CAR&BIKE Manual De Instrucciones página 33

ENGLISH
Product performance
Warning
The motor of this pressure washer does not run continuously. It only runs when pressing the
trigger. Once the initial procedures in this manual have been carried out, turn the pressure
washer on and press the trigger to activate the pressure washer.
Nozzle cleaning
- A clogged or partially clogged nozzle can significantly reduce water output and cause
intermittent jetting. To clean the nozzle:
Turn off and unplug the unit.
-
Disconnect the water supply. Press the trigger 2 or 3 times to release the pressure trapped
-
in the hose.
- Disassemble the wand.
Turn the nozzle to concentrate mode, this will activate the internal blades.
-
Use the cleaning kit provided, or any sharp item to clean the nozzle, e.g. insert an unfolded
-
paper clip into the nozzle hole. Move it inwards and outwards until all dust and dirt is
removed. Fig. 7
Pour water through the nozzle hole into the nozzle in order to clean the dirt remains. To do
-
this, point a lighted garden hose at the nozzle for 30-60 seconds.
High-pressure hose angle to the surface to be cleaned
When spraying water against a surface, the jet achieves maximum impact when sprayed
head-on. However, this type of impact tends to embed dirt particles into the surface, creating
the opposite cleaning effect to the desired. Therefore, the optimum angle for spraying water
against a surface is 45°. Spraying water at this angle improves the impact and allows it to be
combined with more efficient dirt removal.
Fig. 8
Distance from the surface to be cleaned
Another factor that determines the impact force of the water is the distance to the surface
to be cleaned. Impact and force of the water increases as the spray nozzle approaches the
surface.
How to avoid damaging surfaces
A surface is damaged when the impact of the force of the water is greater than the
-
hardness of the surface. The impact force will vary according to the settings mentioned
above. Never use a direct jet on surfaces susceptible to damage. Avoid spraying windows
with the direct jet, as they may break.
Follow these steps to avoid damage to the surfaces:
-
- Before pressing the trigger, move the spray nozzle to the fan spray position.
H I D R O B O O S T 1600 CAR&BIKE
64
- Follow the distance and angle instructions mentioned above.
- Vary the angle of the jet, the type of jet and the distance from the surface to be cleaned
until efficient cleaning is achieved without damaging the surface.
Accessories
3D TurboFlip nozzle
The 3D TurboFlip nozzle, also defined as a rotating nozzle, is a very effective accessory to
significantly reduce cleaning time. It must be used to clean in the turbo mode explained in the
previous section.
Soap bottle
- This model includes an accessory to apply soap while operating. The use of soaps may
reduce the cleaning time and make the dirt removal easier. Some soaps have been designed
for their use in pressure washers and specific cleaning tasks. The use of thick soaps, like
the soap used with tableware, can clog the injection system with chemical products.
- Note: soaps work better when applying them on the spray mode.
- The chemical action combined with high-pressure rinses, in the concentrated mode, is
very effective. In vertical surfaces, apply soap from bottom to top. This will prevent soap
from falling down and creating stains. High-pressure rinses can also be carried out from
bottom to top. With stains specially difficult to remove you may need to use a brush along
with soap and high-pressure rinses. Follow the instructions in the next section to use this
accessory.
Anti-impurities filter
This model includes a transparent male connector with an anti-scale filter which can be
assembled with the hose to prevent limescale build-up.
360Brush (special for wheel rims)
This model includes a specific brush for car rims made of bristles, which can remove the
harshest dirt. When using this accessory, water will automatically come out as spray, at low
pressure.
EasyClean brush (special for gaskets)
This mode also includes a cleaning brush which, combined with water and soap, helps
remove stains and allows for a more efficient cleaning. When using this accessory, water will
automatically come out as spray, at low pressure.
Cleaning process
The following cleaning procedure will help you organise and ensure you get the best results.
Remember to follow the previous advice.
ENGLISH
H I D R O B O O S T 1600 CAR&BIKE
65