Publicidad
Idiomas disponibles
Idiomas disponibles
7. Close the battery compartment cover: align the cover on the
back of the unit and slide it upwards until it snaps into place.
8. Optional: If the external microphone (MIC 014-R) will be used,
plug it into the External Microphone Jack on the top of the unit.
Microphone Use / Installation
Top View:
Battery
Balance
Type*
Adjust
Switch
Left
Right
NiMH
(Mono)
Balance
Alkaline
Control
(Fully
counter-
clockwise
= Mono)
AAA
Batteries
9. Turn ON the Pocketalker by rolling the "Power On/Off Volume
NiMH* or
Adjust" rotary dial (located on the front) towards the top. The
Alkaline*
power "on" green LED indicator on the front of the unit should light
up. As the knob is rotated towards the top, the volume will get
louder.
PRESS HERE
Power On / Volume Adjustment Dial
WHILE SLIDING
SLIDE
Front View:
Battery
Cover
Headphone/
Earphone
Power On
Jack
Volume+
Tone
Adjust
Adjust
Dial
Volume-
Power Off
Tone Adjust
Rotary Dial
10. Adjust the volume up or down according to your preferences
by rotating the volume dial towards the top (for more volume)
or towards the bottom (for less volume).
10
Internal Microphone
External Microphone
Internal Microphone
Jack
Clip
External Microphone
Jack
Clip
Clip
Power "On"
Green LED
Clip
Power On/Off
and
Volume Adjust
Rotary Dial
More
Adjust
treble
T-coil
Switch
Adjust
More
bass
Battery
Compartment
External Microphone
Jack
Clip
Note: The Power "On" Green LED will blink fast when the battery is low.
11. Adjust the tone according to your preferences. Turning
the tone control towards the top (+) boosts the treble (high
frequency). Turning the tone control towards the bottom (-)
boosts the bass (low frequency). The white dot on the dial
indicates the normal position (no treble or bass boost).
Balance
Tone Adjustment Dial
Adjust
Left
Right
Left Side View:
Balance
(Mono)
Balance
Clip
Adjust
Control
(Fully
Left
Right
(Mono)
counter-
More
clockwise
treble
= Mono)
Adjust
More
bass
Battery
Compartment
Using the built-in T-coil with a Loop System
The Pocketalker can be used with loop systems. When the T-coil
Headphone/
switch on the Pocketalker is enabled, the Pocketalker disables
Power On
Earphone
Jack
Volume+
the microphone input, picks up the loop signal, and sends the
Tone
Headphone/
audio through the headphone jack.
Adjust
Adjust
Earphone
Power On
T-Coil Symbol
Lanyard Slot
Dial
Jack
Volume+
To use this feature:
Tone
Volume-
T-Coil "On" LED
Adjust
Power Off
Tone Adjust
Adjust
Follow the "Getting Started" instructions and instead of step 8,
T-Coil Switch
Dial
Rotary Dial
flip the T-coil switch to the "T-coil" position (up towards the T-coil
(in "On" position)
Volume-
symbol). The T-coil "On" LED indicator above the switch will light
Charging LED
Power Off
Tone Adjust
indicator
up.
Rotary Dial
USB Micro-B
Charging Port
clockwise
= Mono)
Headphone/
Earphone
Power On
Volume+
Jack
Tone
Tone
Balance
Adjust
Adjust
Adj.
Control
More
Dial
Dial
(Fully
treble
Volume-
counter-
Power Off
Tone Adjust
clockwise
Adjust
Rotary Dial
= Mono)
More
bass
Normal
position
(dot in
center)
Power "On"
Green LED
Power On/Off
Power "On"
and
Green LED
Volume Adjust
Rotary Dial
Power On/Off
and
T-coil
Volume Adjust
Switch
Rotary Dial
T-coil
Switch
Adjust
More
bass
Normal
position
(dot in
center)
Power "On
Green LED
Front View:
Power On/
and
Volume Ad
Rotary Dial
T-coil
Switch
T-Coil Symbo
T-Coil "On" LE
Lanyard Sl
T-Coi
T-Coil Switch
(in "On" posit
T-Coi
Charging LED
indicator
T-Coi
(in "O
USB Micro-B
Charg
Charging Port
indic
USB
Charg
11
Publicidad
