Reflex Reflexomat RSC Smart Manual De Instrucciones Original página 25

6.4.1.2 Make-up with softening and degassing
Reflexomat RSC Smart and Reflex Servitec S.
1 Reflexomat RSC Smart
2 Reflex Servitec S
3 Reflex Fillsoft
4 Reflex Fillset Impulse
The Reflex Servitec S degassing and make-up unit degasses the water from the
system circuit and the make-up water. The automatic make-up for the system
circuit is controlled by the pressure maintenance system. Reflex Fillsoft additionally
softens or demineralises the make-up water.
•
Reflex Servitec degassing and make-up unit,  4.6 "Optional equipment and
accessories",  22.
•
Reflex Fillsoft softening system and Reflex Fillset Impulse,  4.6 "Optional
equipment and accessories",  22.

Note!
In a setup with a Reflex Fillsoft water treatment system, always install the
Reflex Fillset Impulse.
•
The controller evaluates the make-up quantity and signals the
necessary replacement of the softening or demineralisation
cartridge.
6.5 Power Supply
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
•
Ensure that all phases of the mains power supply to the product are
disconnected prior to installation. (Pull out the power plug.)
•
Ensure that the system is secured and cannot be reactivated by other
persons.
•
Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical
engineering regulations.
All electric connections between control unit and expansion vessel are pre-
installed.
1. Connect the power plug to the 230 V voltage supply.
2. Activate the system.
The electrical connection is completed.
Installation of an RCD with an I∆n value of 30 mA in the input power supply is
recommended.
6.5.1 Terminal diagram
W Make-up line
C
LIS Filling level measurement
EC Expansion line
Reflexomat RSC Smart — 08.01.2024-Rev. A
Item
Terminal
Signal
no.
number
1 GND
RS485 interface for Modbus RTU or
1 2 A
proprietary Reflex protocol
3 B
4 P3 External make-up request
•
2
With the Levelcontrol setting.
5 P4
Input 230 V signal via L+ N
6 WM1
3 ---
7 WM2
8 K1
Contact water meter
4
•
Digital input
9 K2
10 24 V
Filling level measurement
5 11 INP
•
Analogue input 4-20 mA
12 GND
13 WM1
6 ---
14 WM2
15 24 V
Pressure sensor
7 16 INP
•
Analogue input 4-20 mA
17 GND
18 GND
19 24 V
8 ---
20 OUT
21 AIN
22 N
9 Make-up request 230 V
23 M3
24 N
10 Solenoid valve on the air side
25 M2
26 C
Potential-free group alarm contact
11 27 NC
(max. 230 V / 8 A)
28 NO
29 N
12 Compressor/relief valve
30 M1
31 PE Earthing
13
32 PE Earthing
33 PE
230 V voltage supply via cable with
14 34 N
power plug.
35 L
36 24 V
Conductivity measurement
15 37 INP
•
Analogue input 4-20 mA
38 GND
6.5.2 RS-485 interface
This interface is used to retrieve all controller data and to enable communication
with control centres or other devices.
The following data can be requested:
–
Pressure and filling level.
–
Compressor operating states.
–
Make-up operating statuses.
–
Aggregate volume of the FQIRA + contact water meter.
–
All messages,  9.4 "Messages",  29.
–
All entries in the error memory.
Installation
Function Wiring
On-site,
optional
On-site,
optional
---
On-site,
optional
Factory
---
Factory
---
On-site,
optional
Factory
On-site,
optional
Factory
Factory
Factory
Factory
On-site,
Option
English — 25