Makita DUM111 Manual De Instrucciones página 18

Removing the grass receiver
1. Release the protrusions on the grass receiver
from the grooves on the tool while sliding the grass
receiver toward the front of the tool.
► Fig.10: 1. Grass receiver
2.
Release the hinge of the grass receiver from the
tool.
Installing or removing the shear
blades for grass shear
NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
Removing the shear blades
1. Remove the grass receiver if it's installed. Place
the tool upside down.
► Fig.11
2. While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.12: 1. Undercover 2. Lock lever
3.
Remove the undercover, shear blades, and crank.
► Fig.13: 1. Undercover 2. Grass shear blades
3. Crank
Installing the grass shear blades
1. Prepare the crank, undercover, and new grass
shear blades.
► Fig.14: 1. Crank 2. Undercover 3. Grass shear blades
2. Remove the blade cover from the old grass shear
blades, and then attach it to the new ones.
► Fig.15: 1. Blade cover
3. Adjust the three pins so that they are lined up on
the alignment line.
► Fig.16: 1. Alignment line
4.
Apply a small amount of grease to the periphery
of the crank. Attach the crank to the pins with the small
and large rounds facing up.
► Fig.17: 1. Crank
5. Adjust the blades and guide plate so that the hole
in the guide plate and the two protrusions on the blades
are lined up.
► Fig.18: 1. Guide plate
6. Turn the shear blades upside down and install
them so that the pins on the tool fit in the hole on the
guide plate. Make sure that the shear blades are fixed
securely in place.
► Fig.19: 1. Guide plate
NOTE: Sliding the blade cover forward slightly makes
it easier to install the shear blades.
7. Place the undercover so that
cover is aligned with
► Fig.20: 1. Undercover 2. Lock lever
on the undercover is aligned
on the under-
on the lock lever.
8. While pressing the undercover, turn the undercover clockwise
until on the undercover is aligned with
► Fig.21: 1. Undercover 2. Lock lever
9.
Make sure that the lock lever fits in the groove on
the undercover.
► Fig.22: 1. Lock lever
CAUTION:
Never use the tool without install-
ing the undercover.
10. Remove the blade cover, and then turn on the tool
to check that it works properly.
NOTICE:
If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing shear blades
for hedge trimmer
CAUTION:
Attach the blade cover before
removing or installing the shear blades.
NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
Removing the shear blades
1. Place the tool upside down.
► Fig.23
2.
While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.24: 1. Lock lever 2. Undercover
3. Remove the undercover.
► Fig.25: 1. Undercover
4. Loosen two screws with a screwdriver and remove
the shear blades.
► Fig.26: 1. Screws
NOTE: The shear blades can be removed without
removing the screws.
5. Remove the crank from the shear blades.
► Fig.27: 1. Crank
NOTE: The crank may remain in the tool.
NOTE: Attach the blade cover and the storage case to
the removed shear blades, and then store the blades.
Installing hedge trimmer blades
1. Prepare the crank, undercover, and new hedge
trimmer blades.
► Fig.28: 1. Crank 2. Undercover 3. Hedge trimmer blades
2. Attach the blade cover to the hedge trimmer blades.
► Fig.29: 1. Blade cover
3.
Adjust the three pins so that they are lined up on
the alignment line.
► Fig.30: 1. Alignment line
18 ENGLISH
on the lock lever.
on the undercover is aligned