Worx Nitro WG350E. Serie Manual Original página 17

NOTE: Chain life and cutting capacity depend
on optimum lubrication. Therefore, the chain is
automatically oiled during operation.
FILLING OIL TANK:
WARNING: Removing the battery pack before
1. Set chainsaw on any suitable surface with oil
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil until tank is full.
cap and tighten by turning clockwise until hand
tight.
IMPORTANT: To allow venting of the oil
tank, small breather channels are provided
prevent leakage, and ensure machine is left in a
horizontal position when not in use.
It is important to use bar and chain lubricant (not
provided) that is formulated to perform over a wide
can be found at the location where you purchased
this saw or your local hardware store. Do not use
dirty, used or otherwise contaminated oils. Damage
may occur to the bar or chain. Use of non approved
oil will void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store
CHECKING THE AUTOMATIC OILER
Proper functioning of the automatic oiler can be
checked by running the chainsaw and pointing
the tip of the guide chain bar towards a piece of
cardboard or paper on the ground. If an increasing
oil pattern develops on the cardboard, the automatic
despite a full oil reservoir, contact WorxNitro
customer service agent or WorxNitro approved
service agent.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 40cm.
5. OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or
pack connections because of an electrical failure
and hazard will occur.
NOTE: Your battery pack is shipped UNCHARGED
and you must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
20V 30cm Cordless BL ChainSaw
battery charger.
2. CHECKING THE BATTERY CHARGE-LEVEL (See
Fig. G)
The battery level can be known from the battery
indicator light by pressing the button beside the
lights.
Note: Fig. G only applies for the battery pack with
battery indicator light.
3. CHARGING YOUR BATTERY PACK (See Fig. H)
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit. The
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool down
before recharging.
Note: Always fully charge the battery. More details
can be found in charger's manual.
4. TO REMOVE OR INSTALL BATTERY PACK (See
Fig. I)
Depress the battery pack release button to remove
the battery pack from your tool. After recharging,
insert the battery pack into the battery port. A simple
click is heard. Check to see if the battery is fully
secured.
Note: When removing the battery pack, hold it
5. SWITCHING ON AND OFF (SEE FIG. J)
ATTENTION: Check the battery packs before
using your cordless tool. Only use the battery
pack listed in the accessories section.
For switching on the tool, press the lock-out button,
position. The lock-out button can now be released.
For switching off
NOTE: The chain brake must be activated in order
for the saw to be switched on.
6. CHAIN BRAKE (SEE FIG. K)
The chain brake is a safety mechanism activated
through the front hand guard, when kickback occurs.
Chain stops immediately.
The following function check should be carried
out at regular intervals. Pull the front hand guard
towards the operator (position
chain brake. To activate the chain brake, push front
hand guard forwards (position
NOTE: If the saw is unable to start, even though it is
assembled properly and working with a fully charged
battery pack, then you should check if the chain
brake is in the correct position (position
) to deactivate
).
).
EN
17