Publicidad
Idiomas disponibles
Idiomas disponibles
7. CUTTING
level window prior to starting and regularly
level is low. A full oil tank will last approx. 12
minutes of cutting depending on sawing intensity
and stops.
Check recent replaced chain tension about every
10 minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying
on the ground. This will keep the chain from
touching the ground as it cuts through the log.
Touching the ground while the chain is moving is
dangerous and will dull the chain.
(3) Use both hands to grip saw. Always use left
hand to grip front handle and right hand to grip
must wrap around saw handles. (See Fig. M)
shoulder width apart. Distribute your weight
evenly on both feet.
(5) When ready to make a cut, push the lock-out
button completely in with the right thumb and
squeeze the trigger. This will turn saw on.
Releasing the trigger will turn the saw off. Make
sure the saw is running at full speed before
starting a cut.
(6) When starting a cut, slowly place moving chain
against the wood. The wood should be as close
18
in place to avoid possible bouncing or skating
(sideways movement) of saw.
(7) Guide the saw using light pressure and do not
put excessive force on the saw, letting the saw
do its work. The motor will overload and can burn
for which it was intended.
(8) Remove the saw from a cut with the saw running
off trigger. Make sure the chain has stopped
before setting the saw down.
(9) Keep practicing on scrap logs in a secure
working area until you are comfortable, using a
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback guide bar. Both items reduce the chance
of kickback. However, kickback can still occur with
this saw.
The following steps will reduce the risk of kickback.
•
Use both hands to grip saw while saw is running.
around saw handles.
•
Keep all safety items in place on saw. Make sure
they work properly.
•
Do not overreach or cut above shoulder height.
•
Keep solid footing and balance at all times.
20V 30cm Cordless BL ChainSaw
•
Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
•
Do not let guide bar nose touch anything when
chain is moving.
•
Never try cutting through two logs at same time.
Only cut one log at a time.
•
Do not bury the guide bar nose or try plunge cut
(boring into wood using guide bar nose).
•
Watch for shifting of wood or other forces that
may pinch chain.
•
Use extreme caution when reentering a previous
cut.
•
Use only the low-kickback chain and guide
bar that were supplied with this chainsaw or
recommended.
•
Never use a dull or loose chain. Keep chain sharp
with proper tension.
How to use saw safely
1. Use the chainsaw only with secure footing.
2. Hold the chainsaw at the right-hand side of your
body (See Fig. N).
3. The chain must be running at full speed before it
makes contact with the wood.
4. Use the bucking spikes to secure the saw onto
the wood before starting to cut.
5. Use the bucking spikes as a leverage point while
cutting. (See Fig. O)
6. Do not operate the chainsaw with arms fully
extended, attempt to saw areas which are
sawing (See Fig. P).
Never use the chainsaw above shoulder height
CUTTING WOOD UNDER TENSION (SEE FIG. Q)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be
alert for wood springing back. When wood tension
is released, limb could spring back and strike
operator causing severe injury or death.
When sawing logs supported on both ends, start the
below, in order to avoid contact of the chainsaw with
the ground. When sawing logs supported on only
cut from above (Z) in order to avoid log splitting or
6. MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and guide bar
maintenance can reduce chances of kickback. Inspect
and maintain saw after each use. This will increase
the service life of your saw.
Note: Even with proper sharpening, risk of kickback
EN
Publicidad
