Publicidad
Idiomas disponibles
Idiomas disponibles
can increase with each sharpening.
MAINTENANCE AND STORAGE OF Chainsaw
1. Remove the battery pack
•
When not in use
•
Before moving from one place to another
•
Before servicing
•
Before changing accessories or attachments,
such as saw chain and guard
2. Inspect chainsaw before and after each use.
Check saw closely if guard or other part has
been damaged. Check for any damage that
may affect operator safety or operation of saw.
Check for alignment or binding of moving parts.
Check for broken or damaged parts. Do not use
chainsaw if damage affects safety or operation.
Have damage repaired by authorized service
center. To locate an authorized service center,
visit www.worx.com.
3. Maintain chainsaw with care.
•
Never expose saw to rain or direct moisture.
•
Keep chain sharp, clean, and lubricated for better
and safer performance.
•
Follow steps outlined in this manual to sharpen
chain.
•
Keep handles dry, clean, and free of oil and
grease.
•
Keep all screws and nuts tight.
•
Keep battery pack from heat, oil, and sharp
edges.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store chainsaw
•
in a high or locked place, out of children's reach
•
in a dry place
•
with bar and chain cover in place
Bar Maintenance
To maximize bar life, the following bar maintenance
is recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear
to be dirty.
The rails should be cleaned every time the chain is
removed.
To clean the Bar rails:
1. Remove chain cover and bar and chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the bar.
3. Make sure to clean oil passages thoroughly
maintenance:
•
Saw cuts to one side or at an angle.
•
Saw has to be forced through the cut.
•
Inadequate supply of oil to the bar and chain.
Check the condition of the guide bar each time the
20V 30cm Cordless BL ChainSaw
chain is sharpened. A worn guide bar will damage
After each use, remove the battery pack, clean all
sawdust from the guide bar and sprocket hole.
square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove
Replace the guide bar when the groove is worn, the
guide bar is bent or cracked, or when excess heating
or burring of the rails occurs. If replacement is
saw in the repair parts list or on the decal located on
the chain saw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen
or when chain stops. Only use replacement chain
noted in this manual.
Inspect guide bar before sharpening chain. A worn
or damaged guide bar is unsafe. A worn or damaged
guide bar will damage chain. It will also make
cutting harder.
Fit the bar tensioning plate tab into the new bar by
tightening the screw clockwise. The tab protrusion
SHARPENING SAW CHAIN
WARNING: Remove the battery pack before
servicing. Severe injury or death could occur
from electrical shock or body contact with moving
chain.
Cutting edges on chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, guide
bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
LUBRICATE SPROCKET
WARNING: Wear heavy duty gloves when
performing any maintenance or service to
this tool. Always remove the battery pack before
performing any service or maintenance on this
tool.
NOTE: It is not necessary to remove the chain or bar
when lubricating the guide bar sprocket.
1. Clean the bar and sprocket
2. Using a grease gun, insert the tip of the gun into
appears at the outside edge of the sprocket tip
(See Fig. S).
3. To rotate the sprocket pull the chain by hand until
Correct Groove
19
EN
Publicidad
