EINHELL AGILLO 36/255 BL Manual De Instrucciones página 16

injuries of any kind resulting from such misuse.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and layout:
•
Lung damage if no suitable protective dust
mask is used.
•
Damage to hearing if no suitable ear
protection is applied.
•
Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
•
Injury and damage to property caused by
flying parts.
•
Cut injuries if no suitable safety clothing is
used.
Danger!
This electric power tool generates an
electromagnetic fi eld during operation. Under
certain circumstances this fi eld may actively or
passively impede medical implants. To reduce
the risk of serious or fatal injuries, we recommend
persons with medical implants to consult their
doctor and the manufacturer of the medical
implant prior to using the equipment.
4. Technical data
Motor power supply: .............. 36V
No load speed RPM: ................................. 0-6400
Cutting width with blade: ................................ 10"
Cutting width with line: ................................... 12"
Length of line spool: .....................................26 ft.
Line diameter: ............................................. 0.08"
Weight (Tool only): ...................................13.4 lbs
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
Anl_Agillo_36_255_BL_SPK7_USA.indb 16 Anl_Agillo_36_255_BL_SPK7_USA.indb 16
EN
5. Before starting the equipment
Caution! Carry out all the following assembly and
adjustment work without rechargeable batteries –
risk of injury. Wear protective gloves.
Inspect unit before each use. Replace damaged
parts. Check for fuel leaks. Make sure all
fasteners are in place and secure. Replace cutting
attachment parts that are cracked, chipped, or
damaged in any way. Make sure the cutting
attachment is properly installed and securely
fastened. Be sure the cutting attachment
shield is properly attached and in the position
recommended by the manufacturer. Use only
fl exible, nonmetallic line recommended by the
manufacturer. Never use, for example, wire or
wire-rope, which can break off and become a
dangerous projectile.
5.1 Fitting the guard hood (Fig. 3)
Remove the socket head screw from the guard
hood. Push the guard hood (15) onto the mount
on the motor housing as far as it will go and
screw it securely in place with the previously
removed socket head screw (Fig. 3). A blade (Fig.
2/ Item 14) on the underside of the guard hood
automatically cuts the cutting line to the optimum
length. This is provided with a safety guard.
Remove the safety guard before starting work.
5.2 Fitting the additional handle (Fig. 4-8)
Undo the handle screw (Fig. 2/Item 17) and
remove the thrust piece (Fig. 2/Item 5). Fit the
additional handle (16) into the holder (27) such
that the plastic ring (29) lies in the groove (34) on
(2x 18V)
the holder (27) (see detailed drawing 5).
Caution! The additional handle is wrongly fi tted
if the plastic ring (29) lies outside the groove (34)
as shown in the detailed drawing 6. This mistake
can result in damage to the additional handle
during use.
Fasten the additional handle (16) to the thrust
piece (5) by re-tightening the handle screw (17).
Use the two supplied cable clips (26) to fasten the
protective tubing for the cable.
5.3 Fitting the long handle (Fig. 9)
Slot the top part of the long handle (6) into the
bottom part of the long handle (9). Screw the
handle connecting piece (7) to the bottom part of
the long handle with the union nut (8) on the top
part of the long handle.
- 16 -
07.12.2023 14:06:06 07.12.2023 14:06:06