EINHELL AGILLO 36/255 BL Manual De Instrucciones página 17

5.4. Adjusting the angle of the additional
handle (Fig. 7)
To adjust the additional handle to the optimum
working angle, slacken the handle screw (17).
Set the desired tilt of the additional handle (16).
Tighten the handle screw (17) again.
5.5 Removing/fi tting the cutting line unit
(Fig. 10)
Note: The equipment is supplied from the factory
ready for operation with the cutting line.
Warning! Take care not to cut yourself on the
cutting line cutter.
a) Removing the cutting line unit
Press the locking lever (12) forward and turn
the cutting line unit (30) clockwise at the
same time until the locking lever latches in
place. Turn the cutting line unit clockwise and
take it off the motor shaft.
b) Fitting the cutting line unit
Press the locking lever (12) forward and turn
the cutting line unit (30) counterclockwise
onto the motor shaft at the same time until
the locking lever latches in place. Turn the line
cutting unit on the motor shaft until it is tightly
secured. Check whether the cutting line
unit can rotate freely after you let go of the
locking lever. If this is not the case, have the
mechanism checked by an expert.
5.6 Guard hood for use with the cutting blade
(Fig. 11)
Caution! The cutting line cover (13) must be
removed if you want to work with the cutting
blade. Take care not to cut yourself on the cutting
line cutter.
Slacken the two retaining screws (31) on the
cutting line cover.
Start at the side and carefully press in the lugs
and pull the cutting line cover (13) up and off .
5.7 Guard hood for use with the cutting line
(Fig. 11)
Caution! The cutting line cover (13) must be
fi tted if you want to work with the cutting line. Take
care not to cut yourself on the cutting line cutter.
Start at the side and press the lugs of the cutting
line cover back in and secure them with the two
screws (31).
5.8 Fitting/removing the cutting blade
The procedure for fi tting the cutting blade is
shown in Figs. 12 - 14. Note the detailed drawing
15. Warning! Take care not to cut yourself on the
cutting blade.
Anl_Agillo_36_255_BL_SPK7_USA.indb 17 Anl_Agillo_36_255_BL_SPK7_USA.indb 17
EN
a) Fitting the cutting blade
Important! If the spacer between the cutting
blade and the motor housing (detailed drawing
15 / Item 27) slips off the motor shaft (28) during
dismantling, push it back onto the motor shaft as
shown in the drawing.
1. Fit the cutting blade (21) in place.
2. The pressure plate (23) must be fi tted with
the higher edge facing the cutting blade
(detailed drawing 15).
3. Fit the pressure plate cover (24).
4. Screw the size M10 hex nut (25) in place.
Warning! For safety reasons, self-locking
nuts are allowed to be used only once without
exception.
5. Press the locking lever (12) and lock the
motor shaft. Tighten the hex nut using the
multifunction tool (22).
6. Check whether the blade (21) can rotate
freely after you let go of the locking lever.
If this is not the case, have the mechanism
checked by an expert.
b) Removing the cutting blade
Press the locking lever forward and lock the motor
shaft. Unscrew and the hex nut and remove the
pressure plate cover, pressure plate and cutting
blade.
Each time before use, check the following:
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.
5.9 Using the harness
Caution! Always use the harness when working
with the equipment (Fig. 2/Item 20). Always switch
off the equipment before you release the harness
– risk of injury!
•
Fit the harness (Fig. 16)
•
Hook the equipment to the harness (Fig. 17).
•
Adjust to the perfect working and cutting
position using the various harness adjusters
on the harness. The strap attachment (Fig.
18/Item 4) can be moved on the top part of
the long handle if required. To do so, slacken
the wing nut on the strap attachment, move
the strap attachment and then re-tighten the
wing nut.
•
To establish the optimum length of the
harness, you should then make a few
swinging movements without starting the
motor (Fig. 19).
- 17 -
07.12.2023 14:06:06 07.12.2023 14:06:06