cecotec BOLERO COOLMARKET 2D 261 Manual De Instrucciones página 28

ENGLISH
the amount of refrigerant load by the total space of the room in which the refrigerator is
installed must not be less than 8 g/m³.
Note: The amount of refrigerant used by the refrigerator is specified on the appliance marking.
2. Heat dissipation space
During operation, the refrigerator releases heat into the environment. Therefore, you should
leave at least 30 mm of free space at the top chamber, more than 100 mm on both sides, and
more than 50 mm at the rear of the refrigerator.
Dimensions in mm (Fig. 2)
W Depth Height A
540 551 1690 910
Note: Figure 2 is only a schematic diagram of the space required for proper installation.
3. Installation surface
Place the refrigerator on a solid, flat surface (the floor) to keep it stable, otherwise vibrations
and noises will occur. When the refrigerator is placed on a carpet, straw mat, or polyvinyl
chloride, solid support plates should be placed under the refrigerator to avoid colour change
due to heat dissipation.
It is necessary to maintain unobstructed ventilation around the appliance or in an
embedded structure.
Preparing for use
1. Waiting time
Once the refrigerator is correctly installed and clean, do not turn it on immediately, wait at
least 4 hours before connecting it to the power supply to ensure normal operation.
2. Cleaning
Check the placement of the interior accessory parts and clean the inside of the refrigerator
with a soft cloth.
3. Switch-on
Connect the plug into a power socket to switch on the compressor. After one hour, open the
refrigerator door: if the temperature inside the refrigerator compartment has dropped, this
means the cooling system is running normally.
Food storage
4.
After the refrigerator has been in operation for some time, the user may adjust its internal
temperature. Once the refrigerator has reached a suitable interior temperature, put in the food.
If the refrigerator is installed in a wet place, be sure to check if the earth wire and the
B O LE R O COOLM ARKET 2D 26 1 W H ITE
54
B C (°) E F
1054 130±5 50 100
leakage circuit breaker are working normally. If vibration noises occur due to contact of the
refrigerator with the wall or if the wall turns black due to air convection around the compressor,
keep the refrigerator further away from the wall. The installation of the refrigerator may cause
noise interference or image problems in mobile phones, landline phones, radio receivers, or TVs
near the appliance, so in this case, keep the latter as far away from these objects as possible.
Changing the door opening direction
Make sure the refrigerator is unplugged.
1.
2. Lift up and remove the hinge cover, remove the three screws securing the top hinge to the
door, then remove the hinge. Fig. 3
3. Remove the refrigerator-compartment door.
Remove the two screws securing the centre hinge. Fig. 4
4.
5. Remove the freezer-compartment door.
6. Remove the levelling foot from the left side of the refrigerator and set it aside for later
installation. Fig. 5
Remove the screws securing the bottom hinge on the right side of the refrigerator, then
7.
remove the hinge. Fig. 6
8. Remove the washer and nut securing the pin shaft from the right-hand hole in the lower
hinge, then remove the shaft. Fig. 7
Insert the pin shaft into the left hole of the lower hinge, then secure the shaft with the
9.
washer and nut. Fig. 8
10. Install the lower hinge on the left side of the refrigerator.
11. Install the removed levelling foot on the right-hand side of the refrigerator. Fig. 9
12. Remove the screw holding the refrigerator-compartment door stop on the lower-right
side, then remove the door stop and install it on the lower-left side.
Fig. 10
13. Install the refrigerator-compartment door.
14. Move the freezer-compartment door bushing from the top right to the top left. Move the
left hole cover to the right side.
Fig. 11
15. Remove the screw hole cover from the centre-hinge screw hole on the left side of the
refrigerator, then install it into the screw holes on the right side of the refrigerator.
Fig. 12
16. Install the centre hinge on the left side with the two screws removed earlier.
Fig. 13
17. Remove the screw holding the freezer-compartment door stop on the lower-right side,
then remove the door stop and install it on the lower-left side.
Fig. 14
18. Install the freezer-compartment door.
19. Move the freezer-compartment door bushing from the top right to the top left. Move the
cover from the left hole to the right hole.
BOLERO COOLMARKET 2D 261 W HITE
ENGLISH
55