Bimar MDDP-30DEN1-QA3 Manual De Instrucciones página 19

Fax +32 030 9904733
To disable the timer, press (D) and the Off led will light up, pressing it again will light up the On
led, set the time to zero (0.0), after a few seconds the On led will go off and the humidity
percentage in the room will appear on the display.
•
Button " " (E): press the turbo button to select a high or low speed. The "
on the control panel indicates the high fan speed or keeps the maximum moisture; the "
indicator light speed is low, reduces the humidity and is quieter operation.
•
Humidity % regulation: press "▲" to increase the humidity and "▼" to decrease the humidity; the
range of relative humidity between 35% RH and 85% RH, on a scale of 5%; the average value of
60% is recommended. To achieve a drier environment, press "▼" and set a lower percentage. To
achieve a more humid environment, press "▲" and set a higher percentage. While adjusting, the
display should indicate the moisture set. During operation, this indicates the rate of the actual
humidity of the room (precision ± 5%); when the device reaches the humidity set, the
dehumidifier will go on standby.
•
Button " " (E), press to select continuous dehumidification and the corresponding light will
light up; you cannot set the humidity level using this setting.
•
Button " " (G): this check filter function is a reminder to clean the air filter. The filter light
comes on every 250 hours of use. To reset it after having cleaned the filter. press the filter button
and the light will go off.
•
Auto reset: if the unit suddenly stops due to a power failure, it will restart automatically when the
power is restored on the previous function set.
When the dehumidifier operates at low temperatures (12-15°C), there may be a build up of frost on
the evaporator coils; the compressor will stop its cycle and the fan will continue to run until the frost
disappears. If the dehumidifier is blocked, switch off the device and unplug it from the mains, and
then turn it back on. The working temperature of the dehumidifier is between 5-35°C, if the room
temperature is below 5°C, the dehumidifier will not work.
Moreover, the device is equipped with a tank to collect water; the tank must always be fully inserted
or the device will not work and it must be emptied when it is full of water. The appliance is also
equipped with a hole for continuous drainage, with female threaded attachment, the pipe must have
the correct slope to be able to drain continuously, see section: continuous drainage to the outside.
USE
Before each use, ensure that the appliance is in good working order, and that the power cable is not
damaged: if the cable is damaged, it must be replaced by the manufacturer or its service centre or by
someone with a similar qualification in order to prevent any risks. Warning: before the assembling,
disassembling and cleaning of the device, make sure it is disconnected from the mains. There may be
a bit of water left over inside the tank from any testing previously performed.
•
Make sure that if the water is discharged into the tank (not via emptying continuously towards the
outside), check that the cap (8) is placed properly.
•
Plug into the power point and the appliance will beep when it turns on.
•
If you want to program the start-up time, press "
•
Press " ".
•
If you want to program the shutdown time, press "
•
Adjust the humidity using "
•
Press " " to change the fan speed (high or low).
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
".
".
" and " " or select continuous dehumidification with (E).
19
Assembly page 19/61
" indicator light
"