Descargar Imprimir esta página

Max RE-BAR-TIER RB443T Manual De Instrucciones E Instrucciones De Seguridad página 11

Atadora de armaduras de refuerzo

Publicidad

Idiomas disponibles

Idiomas disponibles

• Inspect parts for damage.
Parts will wear over periods of use. Look
also for missing and defective parts and for
parts of poor quality. If a part must be
replaced or repaired, purchase the
replacement part at the dealer where the
tool was purchased or MAX CO., LTD.
authorized distributors.
Use only genuine authorized replacement
parts.
2. SET THE MAIN SWITCH (Fig.6.f) AT
"OFF", THE TRIGGER LOCK (Fig.6.2) AT
"LOCK" AND REMOVE THE BATTERY
PACK (Fig.8), WHEN CHANGING THE
BATTERY PACK, MOVING THE TOOL,
USING THE BELT HOOK, REPAIRING OR
ADJUSTING THE TOOL, REPLACING OR
ADJUSTING THE TIEWIRE WITHOUT
USING THE LOADING ASSIST BUTTON
(READ P.18), ABNORMALITIES OCCUR,
AND THE TOOL IS NOT BEING USED
Leaving the tool switched on in these
situations may cause breakdowns or
damage.
3. KEEP FINGERS AND BODY PARTS
CLEAR BETWEEN THE ARM AND CURL
GUIDE AT ALL TIMES (Fig.24)
Failure to do so may result in serious injury.
4. KEEP FINGERS AND BODY PARTS
AWAY FROM THE TIEWIRE WHEN TOOL
IS IN OPERATION
Failure to do so may result in serious injury.
5. DO NOT POINT THE TOOL AT ANYONE
Personal injury may result if the tool catches
an operator or anyone working near him/her.
While working with the tool, be extremely
careful not to bring hands, legs, and other
body parts near the arm of the tool.
6. WHEN THE TOOL IS NOT IN OPERATION
KEEP YOUR FINGERS OFF THE
TRIGGER
Failure to do so may cause accidental tying,
leading to serious injury.
7. NEVER OPERATE THE TOOL UNDER
ANY ABNORMAL CONDITION
If the tool is not in good working order, or if
any abnormal condition is noticed, switch it
off immediately (set the Main switch at
"OFF"), lock the Trigger and have it
examined and repaired.
8. AFTER BATTERY INSTALLATION IF THE
TOOL OPERATES WITHOUT THE
TRIGGER BEING PULLED OR THE
OPERATOR NOTICES UNUSUAL HEAT,
SMELL, OR SOUND, DISCONTINUE
OPERATION
Failure to do so may lead to serious injury.
Return to dealer for safety inspection.
9. NEVER MODIFY THE TOOL
Modifying the tool will impair performance and
operating safety. Any modification may lead to
serious injury and void the tool warranty.
10. HANDLE THE TOOL WITH CARE.
Dropping it or subjecting it to impact may
result in breakdowns or damage.
11. MAINTAIN THE TOOL IN GOOD
OPERATING CONDITION
To secure operating safety and ensure top
performance, keep the tool free of wear and
damage. Also keep the tool's hand grip dry
and clean, especially free of oil and grease.
12. USE ONLY THE AUTHORIZED BATTERY
PACK
If the tool is connected to a power supply
other than the authorized pack, such as a
rechargeable battery, a dry cell, or a storage
battery for use in automobiles, the tool may
be damaged, break down, overheat, or even
catch on fire. Do not connect this tool to any
power supply except the authorized battery
pack.
13. TO ENSURE MAXIMUM PERFORMANCE,
FULLY CHARGE THE BATTERY BEFORE
USE
A new battery pack or one not used for
extended periods may have self-discharged
and thus may need recharging to restore it to
a fully charged condition. Before operating
the tool, make sure to charge the Battery pack
with the designated MAX Battery charger.
14. BATTERY CHARGING PRECAUTION
14-1 Use only MAX Battery charger and
MAX Battery pack.
Failure to do so may cause the Battery
to overheat or catch fire leading to
serious injury.
11

Publicidad

loading

Este manual también es adecuado para:

Re-bar-tier rb443tce