Publicidad
Idiomas disponibles
Idiomas disponibles
If the Window is dirty and the Feeding
gears position cannot be seen
Open the Window (Fig.1.j) and wipe off the dirt
on the inside of the Window with a cloth. Close
the Window again after cleaning to ensure that
foreign objects will not be able to enter the tool.
2. How to set the Tiewire using the
Loading assist button
This function enables wire ejection and loading/
replacement without pressing the Release
button.
CAUTION
• Wear safety gloves.
• Do not use this function if the surrounding
is too noisy to hear the tool's beep sound.
• Make sure that the Magazine cover
(Fig.12.r) is closed when you start using
this function.
• Confirm that the Window (Fig.1.j) is
closed by tightened Hex bolt (Fig.1.m).
2-1 (Fig.17) Press the Release stopper (9) up
to the top and operate with the Release
button (8) raised up.
2-2 (Fig.6) Set the Main switch (f) at "OFF", the
Trigger lock (2) at "LOCK" and remove the
Battery pack (5).
2-3 (Fig.19) Mount the Battery pack on the tool's
main body until a click is heard.
2-4 (Fig.20) If you set the Main switch at "ON"
and press the Loading assist button (e), a
"piro, piro, piro" sound will notify that the tool
entered "Loading mode".
• "Loading mode" is canceled if 2 minutes
elapse or if you press the Loading assist
button.
• If you press the Loading assist button
again, the tool enters "Loading mode".
Note that the wire is not ejected.
• "Loading mode" will start if you press the
Loading assist button after done tying as
well as immediately after turning the Main
switch at "ON".
2-5 (Fig.21,22) If the Tiewire runs out or if there
is Tiewire left after use, remove them.
2-6 (Fig.13) Feed the wire on the outside of the
Wire feed support (s).
2-7 If you insert the tip of the wire into the Wire
guide, the wire will be grasped automatically
and pulled in approximately 20mm
(approximately 1 inch), and a "pirorin" sound
will notify you that loading is complete.
• If a "puu" sound is emitted, pull the wire out
of the Wire guide. Make sure the feeding
gears are cleared and in closed position.
Press the Loading assist button again and
re-insert the wire.
2-8 (Fig.23) Pull on the wire and make sure it
does not come out of the Feeding gears.
2-9 (Fig.18) Close the Magazine cover and
rotate the Magazine stopper 45° clockwise.
3. How to operate RB443T
WARNING
• (Fig.24) When the Main switch (Fig.1.f) is
turned "ON", the Hook (Fig.1.g) of the tip
rotates automatically for initializing,
absolutely do not bring your fingers close
to any rotating and moving part.
• Do not touch any rotating and moving part
such as hook of the tip or the Tiewire
during the tying work (while the machine is
operating).
(Fig.6) Set the Main switch at "OFF", the
Trigger lock (2) at "LOCK" and remove the
Battery pack (5).
3-1 (Fig.19) Mount the Battery pack on the tool's
main body until a click is heard.
Face the arm downward, and set the Main
switch at "ON".
3-2 (Fig.25) Set the Main switch at "ON" and the
trigger lock (2) at "UNLOCK".
3-3 (Fig.26) Tilt the tool 45° angle to the crossed
rebars.
3-4 (Fig.27) Align the Center mark (a) to the
center of the crossed rebars.
3-5 Once pull the Trigger, the tool automatically
completes a series of tying actions (feeding,
cutting, gripping and tying).
4. How to remove the Tiewire
(Fig.6) Set the Main switch (f) at "OFF", the
Trigger lock (2) at "LOCK" and remove the
Battery pack (5).
18
Publicidad
