Publicidad
Idiomas disponibles
Idiomas disponibles
English
by BLACK+DECKER on this trimmer/edger. Serious injury or
product damage may result.
Reload nylon line (either bulk or prewound replacement
spool) as shown in this manual.
USE ONLY 0.065" (1.65 mm) DIAMETER ROUND NYLON
MONOFILAMENT LINE. Do not use serrated or heavier gauge
line, as they will overload the motor and cause overheating.
This line is available at your local dealer or authorized
service center.
1. Remove battery pack from appliance.
2. Press the release tabs
remove the spool cap from the spool housing
3. For best results, replace spool with BLACK+DECKER
Model AF-100.
22
4. If lever
in base of housing becomes dislodged,
replace in correct position before inserting new spool
into housing.
5. Remove any dirt and grass from the spool cap and
spool housing.
6. Unfasten the end of the cutting line
28
line into the eyelet
.
26
7. Take the new spool
the housing. Rotate the spool slightly until it is seated.
8. The line should protrude approximately 5-3/8" (136 mm)
from the housing.
9. Align the release tabs on the spool cap with the line
27
anchoring slots
in the spool housing.
19
10. Snap the spool cap
20
tabs
and pressing it into the spool housing
snaps securely into place.
nOTE: Make sure that cover is fully positioned. Listen for
two audible clicks to ensure both release tabs are correctly
located. Power the appliance on. In a few seconds or less
you'll hear the nylon line being cut automatically to the
proper length.
nOTE: Other replacement parts (guards, spool caps, etc.)
are available through authorized service centers. To find
your local service location call: 1-800-544-6986 or visit
www.blackanddecker.com.
Rewinding Spool from Bulk Line (Fig. S–V)
Use Only 0.065" (1.65 mm) Diameter, Round
Line
Bulk line is also available for purchase from your
local retailer.
nOTE: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
are recommended.
1. Remove battery pack from appliance.
2. Remove the empty spool from the appliance as
described in Replacing Spool Assembly.
3. Remove any remaining cutting line from the spool.
4. Make a fold at the end of the cutting line
3/4" (19 mm). Feed the cutting line into one of the line
27
anchoring slots
.
5. Insert the 3/4" (19 mm) end of the bulk line into the
30
spool hole
in the spool adjacent to the slot. Make sure
the line is pulled tight against the spool.
12
20
19
on the spool cap
11
25
and guide the
and push it onto the boss
back on by depressing release
11
25
at about
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross.
7. When the wound cutting line reaches the recesses
cut the line.
8. Fit the spool onto the appliance as described in
Replacing Spool Assembly.
MAINTENANCE
WARNING:
, and
serious personal injury, turn unit off and remove
.
the battery pack before making any adjustments or
removing/installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental start‑up
can cause injury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning
WARNING:
23
in
air vents with clean, dry air at least once a week. To minimize
the risk of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts of the
until it
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING:
than those offered by BLACK+DECKER, have not been
tested with this product, use of such accessories with this
product could be hazardous. To reduce the risk of injury, only
BLACK+DECKER recommended accessories should be used
with this product.
Recommended accessories for use with your product
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact BLACK+DECKER.
Call 1-800-544-6986.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING:
and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a BLACK+DECKER factory
service center or a BLACK+DECKER‑authorized service center.
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
29
To reduce the risk of
Blow dirt and dust out of all
Never use solvents or other
Since accessories, other
To assure product SAFETY
,
Publicidad
