Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING
The power supply socket must be protected by a
differential circuit breaker that is in compliance with
current regulations.
7.3 ELECTRICAL SWITCH PANEL
The electrical switch panel is equipped with:
Main switch (a)
•
Boiler thermostat (b)
•
Detergent adjustment tap (c)
•
•
Water pressure gauge (d)
7.4 TANKS
Fill the tanks with their respective products: fuel oil (main filler neck),
detergent (small filler neck). Each tank has an identification label
near its respective filler neck.
7.5 START UP
Fully open the water supply tap.
•
Wait for the internal tank to fill up completely.
•
•
Rotate the SW switch from OFF to ON. The motor will turn on and
the pump will start rotating..
Disengage gun safety lock.
•
Squeeze the trigger on the gun to allow the delivery of
•
pressurized water.
7.5.2 Stop
Rotate the SW switch from ON to OFF.
•
Open the gun and release the pressure inside the piping.
•
Click the gun safety lock to safe
•
7.6 OPERATING PROCEDURES
The SIDRA series high pressure washers are equipped with a "delayed
total lockout system", which stops the machine a few seconds after
the gun is released. Pressing the gun again will cause the machine to
restart normally.
7.7 PRESSURE CONTROL VALVE
The pressure control valve allows the water pressure to be reduced
from its. Reducing this value, the valve partializes the quantity of
water to be heated thus allowing the water's temperature to be
increased. This function is intended to obtain short periods of water
spray at temperatures greater than 100°C (this value is variable
depending on the model and its flow rate).
WARNING
With the water at such high temperatures, great care must
be taken when handling the jet.
WARNING
Prolonged use at high temperatures causes rapid
limescale buildup.
8. ROUTINE MAINTENANCE
WARNING
During routine maintenance, cleaning or extraordinary
maintenance operations, it is mandatory to put on the
personal protective equipment provided.
L-LC056.04-BM
EN
WARNING
Non-compliance with these safety instructions could
result in injury, death or damage to the equipment.
WARNING
All maintenance or cleaning operations are to be carried
out with the machine switched off, the spark plug cable
disconnected and only once the motor has cooled to avoid
burns and fire hazards. No one other than maintenance
personnel should be permitted to approach the machine.
8.1 SAFETY STANDARDS FOR ROUTINE MAINTENANCE
Routine maintenance comprises a series of simple operations to be
carried out at regular intervals and in accordance with the
manufacturer's instructions. The manufacturer has reduced the
number and complexity of the routine maintenance operations so
that they can be performed even by those who do not have
considerable technical skills or complex equipment. Mainly these
include:
Checking pump oil levels using the sight glass on the pump
•
housing
•
Cleaning the fittings and greasing the fittings gaskets
WARNING
If the oil needs to be changed, dispose of the old oil
responsibly in compliance with all current regulations.
Under no circumstances are these substances to be
released into the environment.
8.2 SAFETY STANDARDS FOR CLEANING THE MACHINE
The machine must be stopped and switched off before performing
any cleaning operations.
Comply with the warnings below when cleaning the machine or any
of its parts:
•
Never clean electrical equipment using water or other fluids.
To remove any dust deposits use only a clean brush or a dry cloth.
•
Do not clean plastic surfaces with alcohol, detergents or
•
solvents.
Dispose of cleaning materials responsibly pursuant to current
•
applicable regulations.
•
Do not release used materials or cleaning residues into the
environment.
Clean using water or compressed air and soft cloths.
•
WARNING
During cleaning it is mandatory to put on personal
protective equipment.
8.3 SAFETY STANDARDS FOR REPAIRS AND EXTRAORDINARY
MAINTENANCE
The manufacturer recommends that an authorized repair shop be
contacted for any operations that do not fall under normal
maintenance.
WARNING
These operations are to be carried out only by qualified
personnel, who have all the technical skills to perform
these operations safely and in full compliance with the
applicable laws in force.
It should be pointed out that the right to the warranty offered by the
manufacturer shall be void if:
29 / 48
Publicidad
