Publicidad
Idiomas disponibles
Idiomas disponibles
4.
ÍNDICE
A. ASSEMBLY INSTRUCTIONS
•
Assembly
•
Safety
•
Hooking up
•
Applications
•
Recomendations concerning the work area
B. STARTING THE MACHINE
•
Items to be checked before starting the machine
C. INSTRUCTIONS FOR USE
A.ASSEMBLY INSTRUCTIONS
Assembly
Once you have unpacked your machine, check to make sure that there are no damaged or
broken parts. If there are, and you need to change these components they must only be replaced
by original of the manufacturer, otherwise the CE mark can be not valid (if in doubt, consult the
manufacturer).
Safety
Read carefully and understand the safety measures before the use of the machine.
Hooking up
Check that the voltage and frequency of the machine shown on the characteristics plate match
the electric system. (fig. 1)
Coil feeding cable during transport. Never move the machine by tugging at the cable.
Applications
Use: Models DU are basic machines for the straight or mitred cutting of building materials, and
work by means of a guided bearing system. Such cuts are made with water-cooled diamond
blades.
Recommendations concerning the work area
Pay close attention to the state of the area where the job is to be done. Keep it clean and well
lit. The machine should be kept clean at all times in order to ensure optimum performance and
the safest working conditions.
B. STARTING THE MACHINE
Items to be checked before starting the machine
Before using this machine, verify that no parts are worn out, damaged or broken. Should you find
any part that is not in proper condition, have it repaired or replaced immediately.
Levelling the machine: (fig. 2, 3).
DU
An optional table-stand for placing the machine level with the job is also available.
Check that the stops of the machine are perpendicular to the blade. These are regulated before
leaving the factory. Ensure that the voltage and frequency of the machine shown on the charac-
teristics plate match the electric system. (fig. 1)
The electrical outlet must have an earth connection and protection in the event of leaking (diffe-
rential). When using an extension, check that the cable section is at least 2.5 mm².
The disc cover protection, protects to the user of possible cuts during the work.
C. INSTRUCTIONS FOR USE
1.
To install or replace the blade, first remove the protective cover to reveal the drive. shaft.
Insert the blade between the blade discs, turning in the direction shown on the machine.
Tighten the screw as illustrated. (fig. 4, 5)
2.
Fill the base with water until the water pump is completely covered. Working with clean
water gives your blade longer working life and improved performance. (fig. 6)
3.
Models DU-200-BL are equipped with a table-stand for placing the ceramic tile, and.a
sliding motor unit. This system enables you to handle all types of ceramic tile with maxi-
mum precision and comfort. (fig. 7)
4.
Movement takes place by means of wheels equipped with greased, sealed ball bearings.
5.
To prevent accidents, shut the motor off when changing from the straight cutting position
to that of mitred cutting (and viceversa), changing cutting height and adjusting stops for
repeated cuts. (fig. 8, 9)
6.
The starting of the machine will be made by pressing the tilted switch, and the same to
disconnect. (fig. 10)
7.
DU have a safety system that protects the motor from overheating.
8.
If the motor should stop for no apparent reason, wait a few minutes as it has probably
been overworked. Moderate the speed in subsequent cutting.
9.
Once the machine is operating, wait until the motor and the water supply by the pump
return to normal (4 or 5 seconds).
10.
To make correct cuts, guide the blade firmly and evenly, without brusque. One incorrect
move can break the workpiece and seriously damage the blade.
11.
For 45º cuts (mitred cuts), there is a system of mechanical blockage, which enables you
English
TRANSLATION OF THE ORIGINAL
D. SAFETY INSTRUCTIONS
E. MAINTENANCE
•
F. GENERAL CHARACTERISTICS
•
•
•
•
•
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
D. SAFETY INSTRUCTIONS
Important! When using electrical apparatus, observe the following safety measures
in order to reduce the risk of electric discharge, injuries and fire.
Read and observe all these instructions before using the machine.
KEEP THESE INSTRUCTIONS SOMEWHERE SAFE
Before starting, ensure you use protective gloves , ear protectors and
Although this is a wet saw and little dust is generated during cutting, it is highly recommendable
to wear a protective mask.
Once the job is finished, dispose of dirty water at a public institution of recycling and waste
collection.
Recommended working temperatures should be between 5 and 40 ° C and between 0.8 and
1.1 bar. (maximum humidity 95%).
Do not use the machine for purposes other than those it is designed for.
This machine should only be used with a continuos rin diamond disc. Do not use this
machine with a segmented or turbo disc.
If the disc is mistakenly mounted and when machine is turned on is running in the op-
posite direction, stop the machine and correctly re-mount before commencing any work.
Keep clean the work area
■
Disordered tables and areas are prone to damage
Consider the work area environment
Cleaning and maintenance
Technical characteristics
The overall machine
Accessories
Declaration of compliance with EEC regulations
Electric mitring saws for tiles
to position the head with great precision. (fig. 8, 9)
When the chassis is fixed in place, the moveable stop will be adapted to turn between
-45º, 0º and 45º. This enables you to firmly position the workpieces to be cut, and to
make repeated cuts. (fig. 11, 12)
For the proper functioning of models DU-200 work on level floor surfaces.
Never use diamond blades that are cracked or chipped.
Never use lateral pressure to stop the blades.
Read these instructions carefully before using this product. Keep them in a safe place
for future reference.
Keep cutting tools clean and sharp for better, safer performance:
• Carefully follow instructions when changing accessories.
• Periodically check the cables of this machine. Should they show signs of damage or
wear and tear, have them repaired at an authorised technical service outlet.
• Keep holders clean, dry and free of grease and oil..
Remove wrenches and tools before switching on the machine.
Make sure that the switch is in the "off" position when plugging in the machine.
When using the machine outdoors, use only extensible cord designed for this purpose.
Before using a machine again, check carefully to ensure that it is in proper working.
order for the task you have in mind for it. Any damaged element, whether protective
or not, should be repaired or replaced by an authorised technical service outlet, unless
otherwise specified in this instruction manual. Do not use the machine if it cannot be
switched on and off.
It is essential to have adequate artificial lighting in work areas when the ambient light is
insufficient.
The machine put out off service must be carried out according to the instructions of
each country at a collection point, for proper classification and treatment of materials.
WARNING!
WARNING!
WARNING!
goggles.
Publicidad
