Publicidad
Idiomas disponibles
Idiomas disponibles
2. Tighten the clamping nut (7) using the two-hole as-
sembly key (10) again.
7.5.2
If the grinding disc is thick (Fig. 3,
4)
* = not included in the scope of delivery!
Note:
The collar of the clamping nut points downwards so that
the grinding disc can be attached securely to the recep-
tacle spindle.
1. Push the spindle locking button (5) to block the
gear.
2. Tighten the clamping nut (7) using the two-hole as-
sembly key (10) clockwise.
Note:
If the disc runs unevenly or vibrates after changing, this
disc must be replaced immediately.
• As a precaution after a disc change, allow the prod-
uct to run for 60 seconds at maximum speed. Pay
attention to any unusual noises or sparks.
• Check whether all fastening parts are attached cor-
rectly.
• Make sure that the direction of rotation arrow (if
present) on the cutting or roughing wheels* (includ-
ing diamond cutting wheels*) and the direction of ro-
tation of the product (direction of rotation arrow on
the product head) match.
8
Operation
WARNING
Danger of injury!
Remove the battery from the power tool before carry-
ing out any work on the power tool (e.g. maintenance,
tool change, etc.) and when transporting and storing
it. There is a risk of injury if the on/off switch is oper-
ated unintentionally.
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V gomag series and may
only be operated with batteries of this series. Batter-
ies may only be charged with battery chargers of this
series. Observe the manufacturer's instructions.
8.1
On/Off switch (1) (Fig. 1)
ATTENTION
Before use, check the inserted tool to ensure all fas-
tening parts are attached correctly.
28 | GB
Note:
Always switch the angle grinder on before making con-
tact with the material and then guide the product to the
workpiece.
Note:
If the product blocks due to overload and switches off, it
restarts automatically as soon as the cause of the
blockage is no longer present (auto-start function).
Switching on
1. Switch on the product using the on/off switch (1).
2. Press the start/stop switch (2) to start the product.
CAUTION
Always switch the product off after the work and wait
until the grinding disc has come to a complete stand-
still before placing the product down.
Switching off
1. To switch off, press the on/off switch (1).
2. You can also switch off the product using the start/
stop switch (2).
8.2
Adjusting the speed
Note:
The speed can also be changed during operation.
Use the speed preselection button (6) to preselect the
speed:
1 =
lowest speed, e.g. for surface machining:
Grinding, polishing
6 =
highest speed, e.g. for cut-off grinding
• The set speed level is displayed under the speed
preselection (6).
1. Switch on the product using the on/off switch (1).
2. You can select the speed by pressing the speed
preselection button (6).
We recommend determining the speed using practical
tests.
The speed that makes sense when working depends
on what tasks you are doing with the product.
When cut-off grinding, the use of a high speed is usual-
ly not a problem. When sanding or polishing the surfac-
es, a low speed is better.
9
Working instructions
Note:
Grinding bodies may only be used for the recommend-
ed applications. Otherwise, it could break, be damaged
or cause injuries.
ALWAYS replace the grinding wheel if the product has
been dropped during work.
A grinding or cutting wheel must NEVER be knocked or
banged against the workpiece.
www.scheppach.com
Publicidad
