Nilfisk VHS110 Z22 Manual De Instrucciones página 36

VHS110 Z22
How to replace the Paper Bag
■ Close the inlet by using the relevant cap (if equipped).
■ Release the dust container.
■ Remove the bag and close it with the relevant cap (1) as
shown in the figure.
■ Insert a new bag, making sure the bag inlet is sealed.
■ Set the dust container into the machine again.
How to replace the Safe Bag
■ Remove and put the vacuum hose in a safe and dust-free
place.
■ Close the inlet by using the relevant cap (if equipped).
■ Release the dust container.
■ Close the Safe Bag by pulling the "guillotine" seal (2).
■ Close the plastic bag hermetically using the relevant band
(3).
■ Use the sticky tape (4) to close the bottom of the plastic
bag.
■ Remove the relevant connection (5) of the bag from the
vacuum inlet.
■ Insert a new safe bag, making sure the vacuum inlet is
well connected to the bag attachment, to grant the sealing.
■ Wrap the plastic bag around the dust container external
wall.
■ Place the dust container in the vacuum cleaner.
How to change the Longopac®
Use
■ Loosen the belt (1) and let a portion of the bag slide
downward.
■ Turn the bag full of dust (2) on itself to obtain a section of
coiled bags to be tightened with two clamps (3).
■ Place the two clamps at a distance of 50 mm between
them, then with a pair of scissors cut between the two
clamps.
IT
■ Pull down the bag closed by the band and lay it on the
tray, then tighten the strap (1).
GB
Replacement
■ Loosen the strap (1) and remove the bag holder from its
F
seat.
■ Insert the Longopac
D
holder under the hopper cone, insert the pins into the slots
and turn the system to lock it at the upper cylinder (4).
■ Pull off the Longopac
E
the strap (5) around the support and tighten it, by leaving
free the excess part of the inner end pulled off previously.
■ Remove the outer end of the Longopac® (6) and fold it
downwards, closing it with the clamp (7).
■ Pull down the bag closed by the band and lay it on the
tray, then tighten the strap (1).
C421
Figure 8
Figure 8
Figure 9
in the operating seat, refit the bag
®
inner end for at least 250 mm, place
®
Primary and absolute filter replacement
When the machine is used to vacuum hazardous
substances, the filters become contaminated, therefore:
■ Work with care and avoid spilling the vacuumed
dust and/or material;
■ place the disassembled and/or replaced filter in a
sealed plastic bag;
■ close the bag hermetically;
■ dispose of the filter in accordance with the laws
in force.
Filter replacement is a serious matter. The filter must be
replaced with one of identical characteristics, filtering
surface and category.
Otherwise the machine will not operate correctly.
Before proceeding with these operations, turn off the
machine and remove the plug from the power socket.
Before performing these operations, clean the filter
as described in the "Maintenance, cleaning and
decontamination" paragraph.
Take care not to raise dust during this operation. Wear
a P3 mask and other protective clothing plus protective
gloves (PPE) suited to the hazardous nature of the dust
collected, refer to the laws in force.
Reassemble with care to avoid trapping your hands
between the vacuum unit and the container. Use gloves
that provide protection against mechanical risks (EN
388) with a level of protection CAT. II.
Do not use the Class H filter again after having removed
it from the machine.
Primary filter replacement, for machines equipped
with manual cleaning system
■ Clean the primary filter as described in the "Filter cleaning"
section.
■ Release the closing band (1).
■ Lift the deck and disconnect the grounding braid (2) via
the knob (3).
■ Loosen the filter clamp (4) and lift the Cage (5)
■ Remove and dispose of the filter according to the laws in
force.
■ Restore the vacuum cleaner by inserting a new filter after
fixing it on the cage (5) using the metal clamp (4).
■ Reconnect the grounding braid (2) via the knob (3).
14
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
Figure 10