BFT LEO B CBB 3 230 L02 Instrucciones De Instalación página 38

Logic
Definition
Deadman
HOLD-TO-RUN
Block pulses du-
IBL OPEN
ring opening
Block pulses
|IBL TCA
during TCA
Block pulses
IBL CLOSE
during closing
Open in other
OPEN IN OTHER
direction
DIRECT.
Configuration
of safety input
SAFE 1
SAFE 1.
Configuration
of safety input
SAFE 2
SAFE 2.
Configuration
of safety input
SAFE 3
SAFE 3.
Configuration of
command input
IC 1
IC 1.
Configuration of
command input
IC 2
IC 2.
Configuration of
command input
IC 3
IC 3.
Configuration of
command input
IC 4
IC 4.
Configuration
of the 1st radio
1ch
channel command
Configuration
of the 2nd radio
2ch
channel command
Configuration
of the 3rd radio
3 ch
channel command
Configuration
of the 4th radio
4 ch
channel command
38 -
LEO B CBB 3 230 L02 - LEO B CBB 3 120 F02
INSTALLATION MANUAL
Cross out
Default setting
used
0
1
0
2
0
0
1
0
0
1
0
0
1
0
0
1
0
1
0
2
72
3
4
6
5
74
6
7
8
9*
10*
2
11*
77
12*
13*
14*
0
0
1
61
2
4
3
62
4
2
5
64
3
6
65
0
0
1
2
3
4
9
5
6
7
2
8
9
10
5
11
Pulse operation.
Deadman mode.
Input 61 is configured as OPEN UP.
Input 62 is configured as CLOSE UP.
Operation continues as long as the OPEN UP or CLOSE UP keys are held down.
WARNING: safety devices are not enabled.
Emergency Deadman mode. Usually pulse operation.
If the board fails the safety device tests (photocell or safety edge, Er0x) 3 times in a row, Deadman mode is enabled
which will stay active for 1 minute after the OPEN UP - CLOSE UP keys are released.
Input 61 is configured as OPEN UP.
Input 62 is configured as CLOSE UP.
WARNING: with the device set to Emergency Deadman mode, safety devices are not enabled.
Pulse from inputs configured as Start E, Start I, Ped has effect during opening.
Pulse from inputs configured as Start E, Start I, Ped has no effect during opening.
Pulse from inputs configured as Start E, Start I, Ped has effect during TCA pause.
Pulse from inputs configured as Start E, Start I, Ped has no effect during TCA pause.
Pulse from inputs configured as Start E, Start I, Ped has effect during closing.
Pulse from inputs configured as Start E, Start I, Ped has no effect during closing.
Standard operating mode (Fig.G Rif. 1).
Opens in other direction to standard operating mode (Fig. G Rif.2)
Input configured as Phot (photocell).
Input configured as Phot test (tested photocell).
Input configured as Phot op (photocell active during opening only).
Input configured as Phot op test (tested photocell active during opening only).
Input configured as Phot cl (photocell active during closing only).
Input configured as Phot cl test (tested photocell active during closing only).
Input configured as Bar, safety edge.
Input configured as Bar, tested safety edge.
Input configured as Bar 8k2 (Inactive on SAFE 3).
Input configured as Bar OP, safety edge with inversion active only while opening. If while closing, the movement stops.
Input configured as Bar OP TEST, safety edge tested with inversion active only while opening. If while closing, the
movement stops.
Input configured as Bar OP 8k2, safety edge with inversion active only while opening. If while closing, the movement stops.
(Inactive on SAFE 3).
Input configured as Bar CL, safety edge with inversion active only while closing. If while opening, the movement stops.
Input configured as Bar CL TEST, safety edge tested with inversion active only while closing. If while opening, the
movement stops.
Input configured as Bar CL 8k2, safety edge with inversion active only while closing. If while opening, the movement stops.
(Inactive on SAFE 3).
Input configured as Start E.
Input configured as Start I.
Input configured as Open.
Input configured as Close.
Input configured as Ped.
Input configured as Timer.
Input configured as Timer Pedestrian.
Radio control configured as START E.
Radio control configured as Start I.
Radio control configured as Open.
Radio control configured as Close
Radio control configured as Ped
Radio control configured as STOP
Radio control configured as AUX0 **
Not used
Not used
Radio control configured as AUX3 **
Radio control configured as EXPO1 **
Radio control configured as EXPO2 **
Optional extras