Publicidad
Idiomas disponibles
Idiomas disponibles
take
control
THE STATUS SCREEN DISPLAYS DURING YOUR MASSAGE, PROVIDING
A QUICK REFERENCE FOR THE FOLLOWING INFORMATION
This handy display not only shows the current status for each of the settings, but allows
you to configure each setting right from this screen. Use the up/down navigation buttons
to toggle through the settings; use the right/left buttons to adjust them.
Speed — The back massage speed (not
configurable when Shiatsu or Audio Sync
is selected).
Cloud TCH — The Cloud Touch intensity.
Foot SPD — The underfoot roller speed.
Width — The Tap Touch, Percussion, or Shaitsu
horizontal massage range.
3D — The back massage intensity (not
configurable during a deep tissue massage).
The amount of time remaining
in the current massage session
Illustrates the areas currently being massaged
Menu — Displays the main menu.
Auto — Displays the Auto Programs menu.
When an auto program is running, press
to toggle among the auto programs. The
active program displays at the top of the
status screen.
Cloud — Press to adjust the Cloud Touch
intensity. The selected intensity displays in
the upper left-hand corner of the screen.
Back — Press and hold to recline or
incline the backrest.
Legs Extend — Press and hold to
extend the footrest.
NOTE: During Auto Programs, your
leg length is automatically measured
and the program adjusted accordingly.
If the chair is not in use for three minutes the controller
display automatically shuts down. Press the Stop/Power/
Restore button to resume use. The chair resets all
settings to the default position.
humantouch.com
Indicates if chair is in ZeroG position
Indicates if chair is connected to a
Bluetooth device
The massage techniques currently
in progress
Indicates if heat is on
Stop/Power/Restore — Press this button:
• To power on the remote.
• Select STOP to stop your massage
immediately.
• Select POWER OFF, then select RESTORE
to return the chair to the upright position
before exiting.
Position — Use to move the massage
rollers to the desired position during
AcuPoint
®
detection or when enjoying
a Zone or Spot massage. See Using
Manual Massage Modes on page 8
for more information.
Heat — Press to toggle the heat on and
off. When the heat is on, the heat icon
on the screen displays red.
Legs — Press and hold to raise
or lower the footrest.
ZeroG
— Press and hold to automatically
®
position the chair in ZeroG mode, raising
your feet above your heart for maximum
spine relief.
Legs Retract — Press and hold
to retract the footrest.
If you use your massage chair for more
than an hour continuously it may overheat
and shut down; this is normal. Allow it to
cool for 30 minutes before resuming use.
6
6
Choose from 35 Auto Programs
based on your current need, or configure your own massage
using the Manual Massage screens. You can also control the Cloud Touch air massage
intensity. For an ultra-soothing massage, turn the heat on and connect your smartphone or
tablet to the chair's built-in sound system. Or select Sound Soothe, then choose from eight
relaxing nature sound tracks.
USING THE
AUTO
PROGRAMS
1. From the main menu, select AUTO to display the Auto Programs menu.
AWAKE
- Gets you up and moving for the day.
ENERGIZE
- Soothes and STRETCHES you from head to toe.
PERFORMANCE
- Delivers an intense Cloud Touch air massage.
RECOVERY
- Focuses on relieving tension in the neck and shoulders.
UPPER BACK
- Focuses the massage on your upper back.
LOWER BACK
- Focuses the massage on your lower back.
DEMO
- For a narrated demo of the chair's features, select SETTINGS, then BLUETOOTH to verify that
Bluetooth is turned on. Use the up/down navigation buttons to control the demo volume.
2. Before selecting an auto massage program, make sure your feet are pressed firmly against the bottom
of the foot/calf massage wells. IMPORTANT: Shortly after the massage begins, the foot/calf massager
extends/retracts to measure the length of your legs. The program then uses this information to tailor
your massage to your leg length. If your feet are not pressed firmly against the bottom of the foot/calf
massager, your leg length cannot be measured, and the program will not function properly (for
example, the stretch function will not activate).
3. Select the desired auto program group to display the program list. The primary program displays
at the top of the group, followed by variations of that program.
SHIATSU
- A varied massage, using soft, medium and aggressive intensities.
SWEDISH
- A moderate massage using soft to medium intensity.
SPORTS
- A massage that starts soft and increases to an aggressive intensity.
THAI
- A massage that begins aggressively and decreases to a soft intensity.
NOTE: The Energize auto program massage style also includes an independent Stretch program.
4. Select the desired program. The AcuPoint
maps your massage programs for maximum effectiveness.
5. During auto-detection, you may use the POSITION buttons to manually select your desired shoulder
height.
6. Sit back and enjoy a world-class massage!
NOTE: You cannot access the AcuPoint detection screen after the system has finished the scan. You will
need to power off, restore, and select your desired program again to re-scan your back.
7
®
detection screen displays as it scans your back and
Publicidad
