Publicidad
Idiomas disponibles
Idiomas disponibles
activated for 10 min. from the last button press.
Stop button, movement in progress is immediately cancelled
and the hand control is switched off.
Green light=The hand control is activated
0-20% battery capacity
20-40% battery capacity
40-100% battery capacity
Green light = Mains cable is connected and the product is
charging. The product cannot be used when the mains cable is
connected. If the "Stand By" button is pressed during charging,
the LED will flash and a signal will sound.
Press the button "up" to elevate the seat.
Press the button "down" to lower the seat.
Press the button "backward tilt" to tilt the seat backwards.
Press the button "forward tilt" to tilt the seat forwards.
The hand control is best placed on the upper part of the chassis
("the push handle"), when not in use.
Ensure that the user has the arms on the arm supports and
feet on the foot supports.
Risk of squeezing due to moving parts.
Remaining battery capacity during use:
1. 11+10+9 shines with a steady light from 100%* down to
40%. Then 11 goes out.
2. 10+9 lights up steadily down to 20%*. Then 10 goes out.
3. 9 shines with a steady light down to 11%* when it changes to
a flashing light down to 0%.
*% of total battery capacity
Forward tilted seat can be elevated to maximum 650 mm. If the
seat is elevated higher than 650 mm it cannot be tilted forwards.
Emergency lowering:
If for some reason lowering or tilting the seat with the hand
control is not possible, the emergency lowering button can be
used. Press and hold the button to lower the seat to the lowest
position and tilt the seat up. A signal sounds while the button is
pressed.
The duty cycle printed on the actuator system label must
always be followed. If exceeded, there is a risk that the
actuator system is damaged. The duty cycle is max. 10%,
max. 2 min. in use followed by 18 min. not in use.
Charging
- The device must reach room temperature before charging.
- Charging must only be done in a dry environment and the
electrical connections of the device must be dry before power
is connected.
- Make sure that the mains voltage to be connected to the
product or the system is the one stated on the label.
- Connect the mains cable to the mains socket.
- Fully charge the battery before first use.
- Charge the product when needed, see the lights on the hand
control for remaining battery capacity.
When charging the battery:
1. 9 lights up with flashing light up to 20% *.
2. 9 lights up with steady light +10 lights up with flashing light
up to 40%*.
3. 9+10 lights up with steady light +11 lights up with flashing
light up to 100% and then assumes steady light.
*% of total battery capacity.
All lights go out when the mains cable is removed from the
mains socket.
6
Environmental conditions
Operating:
7
Temperature 5 °C to 40 °C
8
Relative humidity 20% to 80% - non-condensing
9
Atmospheric pressure 700 to 1060 hPa (rated to be operated
at an altitude ≤ 3000 m).
10
Transfer
11
Make sure the castors are locked when the user sits down
or gets up from the chair.
12
Facing the castors outward increases the stability.
13
14
15
Do not stand on the foot plates. Risk of injury if the
16
device tips over.
Do not sit on the front edge of the seat. Risk of injury if the
device tips over.
Moving the device:
Move the chair backwards over a threshold. We recommend
9-11
using a threshold ramp.
When the seat height is set low, the leg supports may catch
on the castors affecting the ability to manoeuvre the chair. To
resolve this, raise the seat height or turn the leg supports to the
side.
Transferring:
Assess the risks and take notes. You as a carer are responsible
for the safety of the user. Aids should be used if the transfer is
deemed as risky, e.g. a suitable floor or ceiling lift. Visit
www.etac.com.
It is important to ensure that the castors are locked and facing
outward before carrying out transfer.
Raise and swivel the leg supports and arm supports to the side
for the user to sit down in or get up out of the chair. Carry out
the transfer.
17
Stationary position:
Always lock as many castors as possible when the chair is used
in a stationary position.
Settings
Settings
Arm supports:
The height of the arm supports and/or width between the arm
supports can be adjusted. Loosen the screws, twist the support
to the desired position and retighten the screws. Then loosen
and refit the arm support plate in the correct position.
Leg supports:
Various height adjustment options are available by moving the
locking pin. The leg supports have 6 different height settings.
Head support:
The head support is adjustable in height, depth and angle and
is laterally settable (see illustrations E5).
21
Etac / Alto / www.etac.com
20
21
18
19-24
See Figure F
1-5
6
Publicidad
