Publicidad
Idiomas disponibles
Idiomas disponibles
Solid Fat
GB
• If you decide to use solid fat, even though it is inadvisable,
heat the oil slowly on the lowest setting until it melts. When
the fat has melted, you can set the appropriate frying temper-
ature.
• When using solid fat, let the fat blocks melt slowly over mod-
erate heat in a normal frying pan. Carefully pour the melted
fat into the deep fryer.
• Remove the deep fryer basket. This prevents the basket from
getting stuck in the solidified fat.
RESET the Hi-limiter (thermal cut-out)
Please note that the RESET button is located at the back of the
detachable rear support with a protective cap (Fig.4 on page 3)
to avoid overheat.
• Unplug the appliance from the electrical outlet first.
• Allow the appliance to completely cool down.
• Unscrew the black protective cap of the RESET button.
• Press the RESET button of the Hi-limiter (thermal cut-out).
You should hear a click sound.
• Screw back the protective cap on the RESET button.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for clean-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
8
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems
Possible cause
The appliance does
Power plug is not
not switch ON.
connected properly
The main switch
with the electrical
does not light up in
power outlet.
green.
The main switch is
not pressed.
The rear support
with heating
element is not
properly mounted.
Inside microswitch
is defective.
The appliance
Hi-limiter (thermal
does not heat up
cut-out) activates.
and temperature
indicator does not
light up. But main
switch lights up in
Hi-limiter (thermal
green.
cut-out) defective.
Temperature
control defective.
Appliance does
Heating element
not reach the set
defective.
temperature after
Temperature
long frying time.
control defective.
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
Possible solution
Make sure the
power plug is
connected properly
with the electrical
power outlet.
Press the main
switch to the "I"
position.
Properly placed the
rear support with
heating element on
the oil container.
Contact the
supplier.
Reset the
Hi-limiter (thermal
cut-out) (See ==>
RESET the thermal
cut-out).
Contact the
supplier.
Contact the
supplier.
Publicidad
