Descargar Imprimir esta página

Roborock S8 MaxV Ultra Manual Del Usuario página 11

Con sistema de relleno y drenaje
Ocultar thumbs Ver también para S8 MaxV Ultra:

Publicidad

Idiomas disponibles

Idiomas disponibles

After cutting the pipe, start by trimming the end to
ensure it forms a straight line rather than a curve, and
then reround it.
Connect to Drainage Pipeline
Connect the cut-to-fit 3/8" pipe to a floor
drain or sewer pipe.
Notes:
Ensure the floor drain or drainpipe outlet is
unobstructed. Avoid inserting the drainpipe into a
sealed chamber to prevent poor drainage.
Ensure the connection between the drainpipe and the
floor drain or sewer pipe is securely fastened.
If other water-using equipment is connected to the
same drainpipe, make sure that their drainage doesn't
disrupt the dock's drainage to prevent leaks.
If necessary, encircle the cut-to-fit harness tube
around both the 1/4" and 3/8" pipes.
Connect the Power Supply
After placing the dock at the location
reserved, open the tap water valve and the
clean water three-way valve. Ensure there
are no leaks throughout the pipeline. Then,
connect the power supply, and make sure
the status indicator light comes on.
Notes:
If the power cord hangs vertically to the ground, it
may be caught by the robot, causing the dock to be
moved or disconnected.
The status indicator light is bright when the dock is
powered on, and dim during robot charging or mop
cloth drying.
The status indicator light turns red if an error occurs.
Place the dock on a hard, flat floor away from fire,
heat, and water. Avoid narrow spaces or locations
where the robot may be suspended in the air.
Placing the dock on a soft surface (carpet/mat) may
cause the dock to tilt and cause docking and departing
problems.
Keep the dock away from direct sunlight or anything
that may block the dock location beacon, otherwise
the robot may fail to return to the dock.
Do not use the dock without the refill and drainage pipes,
high-speed maintenance brush, dust container cover,
disposable dust bag, cleaning tank of edgewise mopping
module, cleaning solution cartridge, or water filter.
Maintain the dock according to the Routine Maintenance.
Do not clean the dock power cord and charging contacts
with a wet cloth or tissue.
All docks are subject to water-based tests before
leaving the factory. It is normal that a small amount of
water remains in the waterway of the dock.
Powering On & Charging
Press and hold
to power on the robot.
Wait until the power indicator light is steady,
and then place the robot in front of the
dock. Make sure that the dock is plugged in.
Then, press
and the robot will automatically
return to the dock for charging. The robot is
equipped with a built-in high-performance
lithium-ion rechargeable battery pack. To
maintain battery performance, keep the
robot charged.
B9-1—
Dock status indicator light dim, robot
power indicator light breathing:
Charging
Note:
The robot may not be turned on when the battery is
low. In this case, place the robot to the dock for charging.
Check the Refill and Drainage
System
To check whether the refill and drainage
system is installed successfully, press and
hold
and
simultaneously for 3 seconds
11
on the docked robot to start a self-check.
During the self-check process, observe
whether the dock can normally fill and drain
water, and check the self-check results.
Note:
The self-check of the refill and drainage system
can be started in the app.
Connecting to the App
1. Download the App
Search for "Roborock" in the App Store
or Google Play or scan the QR code to
download and install the app.
2. Reset WiFi
a. Remove the magnetic top cover and find
the WiFi indicator light.
b. Press and hold
and
simultaneously
until you hear the "Resetting WiFi" voice
message. The reset is complete when
the WiFi indicator light flashes slowly. The
robot will then wait for a connection.
Note:
If you cannot connect to the robot due to your
router configuration, a forgotten password, or any other
reason, reset the WiFi and add your robot as a new device.

Publicidad

loading

Este manual también es adecuado para:

S82usv