Publicidad
Idiomas disponibles
Idiomas disponibles
Please note: to ensure that the water is cold, it is not
possible to perform this activity before 30 minutes have
elapsed from the last cycle (or the last time the product
was powered). During this waiting time, the display will
show the following feedback "WATER IS HOT"
• DESCALE
This special function, activated at regular intervals,
allows you to keep the steam system in the best
condition. Once the function is started, follow all the
steps indicated on the display and press
done to start each phase. The average duration of the
full function is around 100 minutes.
Please note: If the function is stopped at any time, the
entire descaling cycle must be repeated.
The display will show you when it is time to run a
Descale cycle (see the table below).
DESCALE MESSAGE
<RECOMMENDED DESCALE>
It appears after around 15 hours of
steam cycles*
<PLEASE DESCALE>
It appears after around 20 hours of
steam cycles*
*considering the default value (4 - Hard) of water hardness
level. The number of hours of steam cycles that must pass
before the Decale messages are shown depends on the
water hardness level set on the appliance.
The descaling procedure can also be performed whenever
the user desires a deeper cleaning of the internal steam
circuit.
Before to run the descaling phase, the appliance
will check if some residual water is contained into
the boiler, and a Drain cycle could be performed,
if needed. In this case, you will have to empty the
drawer after the Drain cycle, before continuing with
the Descale Phase.
Please note: to ensure that the water is cold, it is not possible
to perform this activity before 30 minutes have elapsed from
the last cycle (or the last time the product was powered).
During this waiting time, the display will show the following
feedback "WATER IS HOT".
PHASE 1/2: DESCALING 70 MIN
When display will show <ADD 0.25 L OF SOLUTION>,
please pour the descaling solution in the drawer. For
best results in descaling, we recommend filling the
tank with a solution composed of 75 g of the specific
WPRO product and 250 ml of drinking water. Make
sure the solution dissolves completely in the water
so that no residue remains. WPRO descaler is the
suggested professional product for the maintenance
of the best performance of your steam function in the
oven. For orders and information contact the after
sales service or www.whirlpool.eu. Whirlpool will
not be held responsible for any damage caused by
the use of other cleaning products available on the
market.
when
MEANING
It is recommended to run a
Descale cycle.
Descale is mandatory. It is
not possible to run a Steam
cycle until a Descale cycle
will be carried out.
1
250 ml
Once the descaling solution is poured inside the
drawer, press
to start the main descaling process.
The descaling phases do not need you to stay in front
of the appliance. After each phase is completed, an
acoustical feedback will be played and the display
will show instructions to proceed with the next
phase.
Once the descaling phase has been completed, the
boiler will be drained: the descaling solution used
during this phase will be poured into the extractable
drawer.
PHASE 2/2: RINSING (30 min.)
To remove descale residuals from the drawer and the
steam circuit, rinse cycle has to be done. When display
shows <ADD 0.25 L OF WATER> fill the tank with 0,25 L
of drinking water, then press
not turn off the oven until all the steps required by the
function have been completed.
When the message "DESCALING COMPLETED" appears
on the display, please press OK to confirm.
Cooking functions cannot be activated during the
cleaning cycle. Please note: A message will be shown
on display, to remind you to execute this operation
regularly.
When Descale procedure is completed, it is suggested
to dry the cavity from potential water residuals. It will
be then possible to use all the steam functions.
Note: during the Descale cycle, some noise could
potentially be heard since the oven pumps are
activated in order to guarantee the optimal descale
efficiency.
Once the maintenance cycle has started, do not remove
the drawer unless requested by the appliance.
. MINUTEMINDER
When the oven is switched off, the display can be
used as a timer. To activate this function, make sure
that the oven is switched off and press
icon will flash on the display.
Press
or
to set the length of time you require and
then press
to activate the timer.
MINUTE-MINDER
An audible signal will sound and the display will
indicate once the minuteminder has finished
counting down the selected time.
= 75 g
+
2
+
3
to start the rinsing. Do
or
: The
Publicidad
