WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this product. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
NOTE: "Mains" is the official UL term for "mains electricity"
referring to grid power delivered to customers and accessed
through a wall outlet.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a ground fault circuit interrupter (GFCI) protected
supply. Use of a GFCI reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
GENERAL SAFETY GUIDELINES
h) Do not let familiarity gained from frequent use of
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
b) Do not use the power tool if the switch does not turn it on
c) Disconnect the plug from the power source and/or remove
d) Store idle power tools out of the reach of children
e) Maintain power tools and accessories. Check for
f) Keep cutting tools sharp and clean. Properly maintained
g) Keep handles and grasping surfaces dry, clean,
5) Service
a) Have your power tool serviced by a qualified
6) SAFETY INSTRUCTIONS SPECIFIC TO USING THE ACS1000
PROJECT TABLE
a) The Project Table is intended for use only with the Kreg
b) Always adjust the height of the guide track to match the
c) When the workpiece is less than 4" [102mm] wide, support
d) Adjust the cutting depth to the thickness of the workpiece.
e) When making a cut where waste portion off the table is
tools allow you to become complacent and ignore
tool-safety principles. A careless action can cause
severe injury within a fraction of a second.
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
the battery pack, if detachable, from the power tool before
making any adjustments, changing accessories, or storing
power tools Such preventive safety measures reduce the
risk of starting the power tool accidentally.
and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool
operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained
power tools.
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
repair person using only identical replacement parts.
This ensures the safety of the power tool is maintained.
saw (item# KPS6512) included with the Plunge Saw (item#
ACS-SAW) as part of the Plunge Saw + Guide Track (item
# ACS2000) and the Master Kit (item# ACS3000). Before
using this product read, understand, and follow the
instructions and safety information included with the saw.
thickness of the workpiece.
the guide track with scrap pieces of the same thickness as
the workpiece to prevent the track from tipping.
Less than ¼"of the blade teeth should protrude through the
workpiece.
larger than the workpiece supported on the table, or
extends more than 12" beyond the table edge, support the
waste portion along the edge of the table as well as toward
the end of the waste piece. A large, unsupported waste
piece can cause the guide track or the table to tip.