Parkside PMRDA 20-Li B2 Manual De Instalación página 13

Clamp the cable end of the boundary wire (11) that extends
away to the rear with the left slot (luster terminal with orange
clamps pointing upwards) of the luster terminal (11.1).
4. Fold the cover (23) upwards.
5. Insert the luster terminal (11.1) into the contact sockets
(25/26) on the charging station (17).
6. Connect the mains plug (15) to the power supply.
7. Check the LED (27) on the charging station.
If the LED (27) lights up green, the boundary wire (11) is con-
nected to the charging station (17) correctly.
Do not place the "protruding" remains of the boundary
wire together. This can lead to faults and failures in the
lawn mower's operation.
Fixing the charging station
The operating range indicator (30) on the charging station
must be located within the restricted lawn area.
:
Illustration
1. Loosen the mounting screws (12) and the hexagon socket
(12.1) from the frame.
2. Place the charging station bumper (18) on the side of the
charging station within the bounded lawn area.
3. Secure the charging station and charging station bumper (18)
in the ground with the mounting screw (12).
The mounting screws (12) are screwed into the ground with
the enclosed hex key (12.1).
Initial start-up
Switching on the lawn mower
1. Press and hold the START button (3) for approx. 3 seconds
until the display (10) lights up.
2. Set the desired language. Select with the arrow buttons (6)
and confirm the selection with the OK button (7).
3. Set the date and time with the arrow buttons (6).
Confirm the selection with the OK button (7). The individual
positions can be navigated with the OK button (7) (skip the
right).
The correct date and time setting is required to ensure the
correct function of the operating time settings.
Number for PIN / 1
4. Press the OK button (7) to enter the main menu.
The lawn mower is now in standby mode.
Changing the PIN
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN.
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Settings".
5. Confirm the selection with the OK button (7).
6. Use the arrow buttons (6) to select "Change PIN".
7. Confirm the selection with the OK button (7).
8. Enter the old 4-digit PIN. If you have entered the PIN incorrect-
ly, use the back button (5) to return to the PIN entry.
9. Now enter a new PIN.
10. C onfirm the new PIN by entering it again. If you have entered
the PIN incorrectly, return to the PIN entry with the back but-
ton (5) and repeat steps 8 and 9.
/ 2 3 4
11. Y ou can recognise a successful change when "Successful!"
appears on the display (10). Return to the main menu with the
back button (5).
Setting/deleting a schedule
Setting a schedule
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN.
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Schedule".
5. Select the day you want to set (Mon, Tue, Wed, Thu, Fri, Sat,
Sun) with the arrow buttons (6).
6. Press the OK button to enter the day setting.
7. Select the start and end time with the arrow buttons (6).
Two mowing periods can be set per day.
Press the OK button (7) to confirm and the selection re-
8.
turns to the left of the day.
If you only want to set a mowing period, return to the
day or to the main menu with the back button (5).
9. Repeat steps 5.-8. to select the schedule period for each day
of the week.
10. P ress the OK button (7) to confirm the result of this setting.
Deleting a schedule
1. Move the selection with the arrow buttons (6) to "All" (top
left).
2. Press and hold the back button (5) to delete the entire sched-
ule for the week.
Setting the operating times
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN.
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Settings".
5. Confirm the selection with the OK button (7).
6. Use the arrow buttons (6) to select "Operating time".
7. Confirm the selection with the OK button (7).
8. Select the desired operating time with the arrow buttons.
You set the operating time in full hours per day.
Confirm the selection with the OK button (7).
9
10. R eturn to the main menu with the back button (5).
When the set operating time per day is reached, the lawn
mower automatically returns to the charging station. An ex-
tension of the operating time during rain breaks can be set direct-
ly via the lawn mower, see section "Setting the rain sensor" or via
the Parkside App: Settings > Rain Sensor.
Setting secondary areas
In highly angular gardens, the area output can be improved,
by setting secondary starting points. In this case, several starting
points can be selected on the perimeter wire.
This allows the robotic mower to reach areas of your garden that
are difficult to access.
The robotic mower will travel the selected distance along the
boundary wire and start mowing in this area.
You can freely choose 5 further starting points. To do this, meas-
ure the distance between the charging station and the starting
point clockwise along the perimeter wire. You use the frequency
in percent to determine how often the robotic mower starts its
work from the charging station or from the respective starting
points. The mowing procedure is still chaotic in this mode.
The secondary starting points are automatically approached dur-
ing operating hours and according to schedule.
GB MT
13