Parkside PMRDA 20-Li B2 Manual De Instalación página 14

GB MT
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN.
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Secondary areas".
5. Press the OK button to select a secondary range (Areas). Se-
lect the starting distance "Distance (dst)m" and the ratio "Per-
cent (pct)%" of the area to be mowed with the arrow buttons
(6) and press the OK button to confirm. After the selection,
you automatically return to the overview of the secondary are-
as.
6. Repeat step 5 to complete the setting of each secondary area
(Areas).
7. Press the OK button (7) to confirm the result of the setting.
The lawn mower travels the distance "Distance (dst) m"
specified by you along the boundary wire (1 - 500 metres)
and then starts mowing.
You can specify the frequency under "Percent (pct)%" to
determine how often the robotic mower starts its work from
the charging station or from the respective starting points.
The sum of the "Percent (pct)%" indication of the 5 secondary
ranges (Areas) must be less than/equal to 100 %.
Spot mode / fixed point mowing
This function allows you to mow lawns that are otherwise covered
by seating furniture, playground equipment or similar.
1. Place the mower on the target area of the lawn.
2. If necessary, open the cover (1).
3. Unlock the display (10) with the 4-digit PIN.
4. Press the OK button (7) to enter the main menu.
5. Select "Spot mode" with the arrow buttons (6).
The display shows "Close the cover to start".
6. Close the cover (1) and the mower starts mowing with the
fixed point.
The lawn mower mows in an anticlockwise spiral direction
and switches to "Automatic mowing" after a mowing radi-
us of 1 m or 3.5 minutes of mowing.
If the mower encounters an obstacle, the mower stops, the dis-
play indicates that mowing has stopped and the mower switches
to standby mode.
When the lawn mower hits the boundary wire (11), it continues
mowing in the opposite spiral direction.
If the mower is outside the boundary wire (11) or on the
charging station and you select "Spot mode", the display
shows "Please place inside the boundary and try again". Set the
mower down inside the boundary wire (11) and next to the
charging station and restart "Spot mode".
If the battery charge level is less than 30 %, the display
shows "Low battery voltage" after 2 seconds. Charge the
lawn mower before you can start mowing with the fixed point.
Setting the rain sensor
Never operate the lawn mower during storms
and make sure to disconnect the charging sta-
tion from the mains.
If the rain sensor is switched on, the lawn mower returns to the
charging station when it rains. The rain sensor is always activat-
ed in the delivery state.
14
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN.
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Settings".
5. Confirm the selection with the OK button (7).
6. Use the arrow buttons (6) to select "Rain mode".
7. Confirm the selection with the OK button (7).
8. To deactivate the rain sensor, select "Deactivate" and confirm
the selection with the OK button (7).
To activate the rain sensor, select "Activate" and confirm the
selection with the OK button (7).
Select a time in minutes when the lawn mower should
start operating again after the rain.
Decide also whether the lawn mower should make up for the
break in operating time caused by the rain.
Confirm each selection with the OK button (7).
9. Return to the main menu with the back button (5).
We advise against having the lawn mower operate while
it is raining.
Working instructions
Regular mowing stimulates the grass to an increased leaf forma-
tion, while at the same time killing weeds. As a result, the lawn
becomes denser after each mowing and an evenly resilient lawn
is created.
The first cut takes place roughly in April when the grass is about
7 - 8 cm high. During the main growing season, the lawn is
mowed at least once a week.
Setting the cutting height
Switch off the device and wait for the blades to come to a
stop. There is a risk of personal injury.
1. Open the cover (1).
2. Set the rotary wheel (2) to the desired cutting height.
3. Close the cover (1) again.
The device can be adjusted in 15 steps to a cutting height be-
tween 25 - 60 mm.
The correct cutting height is between 30 and 45 mm for an orna-
mental lawn and about 30 to 65 mm for a utility lawn.
A high cutting height should be selected for the first cuts in
the season.
Manually interrupting/starting the
operating cycle
Interrupting operation
Press the STOP button (9) to stop the mower during operation.
Starting/resuming operation
1. Open the cover (1).
2. Confirm the selection with the OK button (7).
3. Unlock the display (10) with the 4-digit PIN.
4. Press the start button (3).
5. Close the cover (1) again.
The lawn mower starts the set operating cycle or resumes its
previous activity without interruption.