All Models - Yamaha XP7000 Manual De Instrucciones

All Models

Power Bandwidth
THD+N
Intermoduration Distortion
Frequency Response
Channel Separation
Residual Noise
Damping Factor
Voltage Gain
Input Sensitivity (dBu)
Maximum Input Voltage
Input Impedance
Controls
Connectors
Indicators
Load Protection
Amplifier Protection
Power Supply Protection
Cooling
Power Requirements
Dimensions (W x H x D)
Weight
Included Accessories
* These specifications apply to rated power supplies of 120V, 230V and 240V.
0 dBu=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power)
Specifications and descriptions in this owner's manual are for information pur-
poses only.
Yamaha Corp. reserves the right to change or modify products or specifica-
tions at any time without prior notice. Since specifications, equipment or
options may not be the same in every locale, please check with your Yamaha
dealer.
14
XP7000/XP5000/XP3500/XP2500/XP1000 Owner's Manual
Half Power, THD+N= 0.5 %
20 Hz–20 kHz, Half Power
60 Hz:7 kHz, 4:1, Half Power
RL=8 Ω, Po=1 W, HPF=OFF
20 Hz-50 kHz
Half Power, RL=8 Ω, 1 kHz,
Att. max, input 600 Ω shunt
20 Hz–20 kHz, Att. min,
(DIN AUDIO)
RL=8 Ω, 1 kHz
Att. max
Att. max
(Rated Power 8 Ω,
20Hz–20kHz, THD+N = 0.1%)
Front Panel
Rear Panel
Input
Output
MONITOR/REMOTE
POWER/STANDBY
SIGNAL
CLIP/LIMIT
PROTECTION/TEMP
MIN 10 Hz-40 kHz
MAX 0.1 %
MAX 0.1 %
MAX 0 dB
TYP 0 dB
MIN -1 dB
MIN 70 dB
MAX -70 dBu
MIN 350 (XP7000, XP5000), 200 (XP3500, XP2500, XP1000)
XP7000 XP5000
TYP Selectable from 32 dB or 26 dB (or +4 dBu input sensitivity) by select switch
+4 dBu
35.7 dB 34.2 dB
position
XP7000 XP5000
+4 dBu
+4 dBu +4 dBu
position
+13.7 dBu
(120V / 240V)
26 dB
+12.2 dBu
position
+13.6 dBu
(230V)
+7.7 dBu
(120V / 240V)
32 dB
+6.2 dBu
position
+7.6 dBu
(230V)
MIN +22 dBu
TYP 20 kΩ (balanced), 10 kΩ (unbalanced)
POWER switch (push on/push off)
attenuator (31 position) x 2
MODE switch (STEREO/BRIDGED/PARALLEL) x 1
HPF switch (20 Hz/55 Hz/OFF 12 dB/oct) x 2
GAIN SELECT switch (32 dB/26 dB/+4 dBu) x 1
XLR-3-31 type/ch, Euroblock connector (balanced) /ch
SPEAKON/ch, 5 way binding post x 1
Dsub 15 P x 1
x 1 (Green/Orange)
x 2 (Green)
x 2 (Red)
x 1 (Red)
x 1 (Red) heatsink temp. ≥ 85 °C
POWER switch on/off mute
DC-fault:
power supply shutdown/operation not restored automatically. (XP7000, XP5000)
output relay off/restored automatically. (XP3500, XP2500, XP1000)
Clip limiting : THD ≥ 0.5 %
Thermal:
Cuts the output (heatsink temp. ≥ 90 °C) ; operation not restored automatically.
VI limiter (RL ≤ 1 Ω
): Limit the output.
Thermal:
Power supply shutdown (heatsink temp. ≥ 100 °C) ; operation not restored auto-
matically. (XP7000, XP5000).
power supply shutdown (transfomer temp. ≥ 130 °C)
; restored automatically. (XP3500, XP2500, XP1000)
Variable-speed fan: x 1(XP3500, XP2500, XP1000), x 2 (XP7000, XP5000)
Fan stop at heatsink temp. < 55 °C
120V, 220V–240V; 50Hz/60Hz
480 x 88 x 456 mm (18-7/8" x 3-7/16" x 17-15/16")
XP7000 XP5000
14.0 kg 14.0 kg
(30.9 lbs) (30.9 lbs)
Security cover (with a hex wrench), Owner's Manual
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: XP7000/5000 25A , XP3500 22A, XP2500 20A, XP1000 14A
Conforms to Environments: E1, E2, E3 and E4
XP3500 XP2500
32.7 dB 31.2 dB
XP3500 XP2500
+4 dBu +4 dBu
+10.7 dBu +9.2 dBu
+4.7 dBu +3.2 dBu
XP3500 XP2500
15.0 kg 14.0 kg
(33.1 lbs) (30.9 lbs)
XP1000
27.2 dB
XP1000
+4 dBu
+5.2 dBu
-0.8 dBu
XP1000
12 kg
(26.5 lbs)