Display Dimmer Setting; Adjusting The Torque To Rotate The Turntable At A Constant Speed; Maintenance - Technics SP-10R Instrucciones De Funcionamiento

Operation and display of the control unit

Display dimmer setting

The display dimmer will be activated if the
control unit is not operated for 20 seconds.
There are four dimming patterns.
1
On the control unit, hold [RESET]
down and press [DISPLAY].
z The dimmer setting is displayed.
2
Press [DISPLAY] on the control unit.
The setting changes each time [DISPLAY] is
pressed. (See below.)
z The display returns to the original display
if no operation is performed within three
seconds.
33
33.33
[RESET][DISPLAY]
Display OFF
(Initial setting)
[DISPLAY]
Dimmer OFF
[DISPLAY]
Dimmer 1
[DISPLAY]
Dimmer 2
Display dimmer when no operation
Display
is performed for 20 seconds
Brightness is reduced by one level.
⇒ (No operation for further five seconds)
⇒ Brightness is reduced by two levels.
Display OFF
⇒ (No operation for further five seconds)
⇒ Off
Dimmer OFF No dimming (Always on)
Dimmer 1
Brightness is reduced by one level.
Dimmer 2
Brightness is reduced by two levels.
z After setting, brightness is immediately adjusted
to the set value. The display is immediately turned
off if "Display OFF" is selected.
z Operating a button (any button other than
the power button) on the control unit while
the dimmer is active returns the display to full
brightness.
Note
z The setting is saved. When the power is turned on
the next time, the setting when the power was
turned off last will be recovered.
22
(22)
English
(continued)
Adjusting the torque to rotate
the turntable at a constant speed
Press [START·STOP] and then adjust the torque
(rotational force) at five levels to rotate the
turntable at a constant speed.
1
On the control unit, hold [RESET]
down and press [-] and [+]
simultaneously.
z The torque setting is displayed.
2
Press [-] or [+] on the control unit
to make adjustment.
z Select one of the five levels from
"TORQUE1" to "TORQUE5".
Pressing the button increases or
decreases the value.
z Use the table below as a guide.
z The display returns to the original display
if no operation is performed within three
seconds.
33
33.33
[RESET][ ー ][ ＋ ]
TORQUE 5
(Initial setting)
↑
[+] [-]
TORQUE 1
Torque to rotate at a
Display
constant speed
TORQUE5 Maximum (Initial setting)
TORQUE4
TORQUE3
TORQUE2
TORQUE1 Minimum
Note
z The setting is saved. When the power is turned on
the next time, the setting when the power was
turned off last will be recovered.

Maintenance

Cleaning the main unit
„
Wipe the main unit and other components
with a dry soft cloth.
When dirt is heavy, wring a wet cloth tightly to
wipe the dirt, and then wipe it with a soft cloth.
z Do not use solvents including benzene,
thinner, alcohol, kitchen detergent, a
chemical wiper, etc. This might cause the
exterior case to be deformed or the coating
to come off.
„ Moving the unit
Repackage the unit in the packaging it came
in. ( 12)
Keep the packaging materials after taking out
the goods.
If you no longer have the packaging, do the
following:
z Take off the turntable and turntable mat and
carefully wrap them.
z Carefully wrap the main unit in a blanket or
paper.
Repackaging
WEEE symbol
„
Disposal of the product outside the EU
countries
This symbol is valid within the EU
only.
Contact a local governmental office
or your dealer to confirm a right
manner of disposal.
(23)
English
23