Type 8: Automatic Choke/Fixed Throttle; Type 9: Automatic Choke/Remote Throttle/ Flywheel Brake - Honda GCV160 Manual Del Propietário

00X39Z0LA240.book Page 6 Wednesday, March 4, 2009 8:05 AM
Stopping the Engine
1. Disengage the blade brake clutch control lever (see equipment
manual).
2. Move the choke/throttle/stop lever to the SLOW position and allow
the engine to idle for a few seconds.
3. Move the choke/throttle/stop lever to the STOP position.
4. Turn the fuel valve OFF (see TYPE 1 Step 1 on page 3).
TYPE 7: ELECTRIC START WITH ENGINE-MOUNTED
STARTER SWITCH/ MANUAL CHOKE
CONTROL/FIXED THROTTLE
Starting the Engine
1. Turn the fuel valve to the ON
position (see TYPE 1 Step 1
on page 3).
2. Pull the choke rod to the ON
position (see TYPE 5 Step 2
on page 5) (cold engine).
3. Start the engine.
Electric Starter Types
Turn the starter switch to the START position and hold it there until
the engine starts. When the engine starts, allow the starter switch
to return to the ON position.
NOTICE
Do not use the starter for more than 5 seconds or starter motor
damage may occur. If the engine fails to start, release the switch
and wait 10 seconds before operating the starter again.
Recoil Starter Types
a. Turn the starter switch to the RUN position.
b. Pull the starter grip lightly until resistance is felt, then pull briskly
(see TYPE 1 Step 4 on page 4).
4. If the choke was used to start the engine, move the choke rod to
the OFF position as soon as the engine warms up enough to run
smoothly without use of the choke.
The engine speed is preset on this type.
Stopping the Engine
1. Move the starter switch to the STOP position.
2. Turn the fuel valve to the OFF position (see TYPE 1 Step 1 on
page 3).
6
STARTER
SWITCH ON
STOP
START

TYPE 8: AUTOMATIC CHOKE/FIXED THROTTLE

Starting the Engine
1. Turn the fuel valve to the ON
position (see TYPE 1 Step 1
on page 3).
2. Move the flywheel brake lever
to the RUN position.
3. Pull the starter grip lightly until
resistance is felt, then pull
briskly (see TYPE 1 Step 4 on
page 4).
Stopping the Engine
1. Release the flywheel brake lever to activate the flywheel brake and
stop the engine.
2. Turn the fuel valve to the OFF position (see TYPE 1 Step 1 on
page 3).
TYPE 9: AUTOMATIC CHOKE/REMOTE THROTTLE/
FLYWHEEL BRAKE
Starting the Engine
1. Turn the fuel valve to the
ON position (see TYPE 1
Step 1 on page 3).
2. Position the throttle control
so the throttle lever moves
to the FAST position (see
the equipment manual).
3. Position the flywheel
brake control so the
flywheel brake lever is in
the RUN position (see
the equipment manual).
4. Pull the starter grip lightly
until resistance is felt,
then pull briskly (see
TYPE 1 Step 4 on
page 4).
Throttle Setting
Position the throttle control for the desired engine speed. For best
engine performance, it is recommended the engine be operated with
the throttle in the FAST (or high) position.
Stopping The Engine
1. Move the throttle control to the
SLOW position.
2. Release the flywheel
brake lever to stop the
engine.
3. Turn the fuel valve to
the OFF position (see
TYPE 1 Step 1 on
page 3).
ENGLISH
FLYWHEEL BRAKE CONTROL CABLE
FUEL VALVE
LEVER
SLOW
FAST
THROTTLE
LEVER
FLYWHEEL
BRAKE LEVER
SLOW
FAST
THROTTLE
LEVER
FLYWHEEL
BRAKE LEVER