Roland JV-1010 Manual Del Usuario página 70

Aplicación MIDI
❍Effect 3 (Chorus Send Level) (Controller number 93)
status 2nd byte
BnH 5DH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Chorus Send Level: 00H - 7FH (0 - 127)
* In Performance mode, the Chorus Send Level parameter of each Part will change.
❍RPN MSB/LSB (Controller number 100,101)
status 2nd byte
BnH 65H
BnH 64H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm=MSB of the parameter number specified by RPN
ll=LSB of the parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
parameters whose function is defined in the MIDI specification.
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
order) is transmitted to specify the parameter you wish to control. Then, Data Entry
messages (Controller numbers 6 and 38) are used to set the value of the specified parameter.
Once a RPN parameter has been specified, all further Data Entry messages on that channel
are considered to apply to that specified parameter. In order to prevent accidents, when the
desired setting has been made for the parameter, it is recommended that RPN be set to Null.
This device receives the following RPNs.
RPN Data entry
MSB LSB MSB LSB
00H 00H mmH -
00H 01H mmH llH
00H 02H mmH -
7FH 7FH - -
G Program Change
status 2nd byte
CnH ppH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
pp=Program number: 00H - 7FH (prog.1 - prog.128)
* Not received when the Receive Program Change is OFF.
* When received on the Control channel, the Performance will change.
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
70
3rd byte
vvH
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 0CH (0 - 12 semitones)
ll: ignored (processed as 00H)
Up to 1 octave can be specified in semitone steps.
* The Bend Range Up/Down will also be
changed.
* Not received by the Rhythm Part (Part 10).
Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-8192 x 50 / 8192 - 0 - +8192 x 50 / 8192 cent)
* In Patch mode, the Master Tune (SYSTEM)
will change.
* In Performance mode, the Fine Tune
(PERFORM) of each Part will change. When
received on the Control channel, the Master
Tune (SYSTEM) will change.
Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* Not received in Patch mode.
* In Performance mode, the Coarse Tune
(PERFORM/PART) of each Part will change.
RPN null
RPN and NRPN will be set as "unspecified".
Once this setting has been made, subsequent
Data Entry messages will be ignored. (It is not
necessary to transmit Data Entry for RPN Null
settings.
Parameter values that were previously set will
not change.
mm, ll: ignored
G Channel Aftertouch
status 2nd byte
DnH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Channel Aftertouch: 00H - 7FH (0 - 127)
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
G Pitch Bend Change
status 2nd byte
EnH llH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
I Channel Mode Messages
G All Sound Off (Controller number 120)
status 2nd byte
BnH 78H
n=MIDI channel: 0H - FH (ch.1 - ch.16)
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
G Reset All Controllers (Controller number 121)
status 2nd byte
BnH 79H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
* Not received in Performance mode when the Receive Switch (PERFORM/PART) is OFF.
* When this message is received, the following controllers will be set to their reset values.
Controller
Pitch Bend Change
Polyphonic Key Pressure
Channel Pressure
Modulation
Breath type
Expression
Hold 1
Sostenuto
Soft
Hold 2
RPN
NRPN
System General purpose controller 1
System General purpose controller 2
G All Note Off (Controller number 123)
status 2nd byte
BnH 7BH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
* When All Note Off is received, all currently sounding notes of the corresponding
channel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held
until these are turned off.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.
G Omni Off (Controller number 124)
status 2nd byte
BnH 7CH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
* The same processing as when All Note Off is received will be done.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.
3rd byte
mmH
3rd byte
00H
3rd byte
00H
Reset value
[+-]0 (center)
0 (off)
0 (off)
0 (off)
0 (minimum)
127 (maximum)
However the controller will be at minimum.
0 (off)
0 (off)
0 (off)
0 (off)
Unset. Previously set data will not change.
Unset. Previously set data will not change.
0 (minimum)
0 (minimum)
3rd byte
00H
3rd byte
00H