G Omni On (Controller number 125)
status
2nd byte
BnH
7DH
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
* The same processing as when All Note Off is received will be done. The instrument will
not be set to OMNI ON.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.
G Mono (Controller number 126)
status
2nd byte
BnH
7EH
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
mm=Mono number:
00H - 10H (0 - 16)
* The same processing as when All Note Off is received will be done, and the Key Assign
Mode (PATCH) will be set to SOLO.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.
G Poly (Controller number 127)
status
2nd byte
BnH
7FH
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
* The same processing as when All Note Off is received will be done, and the Key Assign
Mode (PATCH) will be set to POLY.
* Not received in Performance mode if the Receive Switch (PERFORM/PART) is OFF.
I System Realtime Messages
G Timing Clock
status
F8H
* This message will be received if the Clock Source (SYSTEM) is MIDI.
G Active Sensing
status
FEH
* When an Active Sensing message is received, the unit will begin monitoring the interval
at which MIDI messages are received. During monitoring, if more than 420 ms passes
without a message being received, the same processing will be done as when All Sound
Off, All Note Off, and Reset All Controllers messages are received. Then monitoring will
be halted.
I System Exclusive Messages
status
data byte
F0H
iiH, ddH, ......, eeH
F0H:
System Exclusive message status
ii = ID number:
This is the ID number (manufacturer ID) that specifies the
manufacturer whose exclusive message this is. Roland's manufacturer
ID is 41H.ID numbers 7EH and 7FH are defined in an expansion of the
MIDI standard as Universal Non-realtime messages (7EH) and
Universal Realtime Messages (7FH).
dd,..., ee = data:
00H - 7FH (0 - 127)
F7H:
EOX (End Of Exclusive)
Of the System Exclusive messages received by this device, the Universal Non-realtime
messages and the Universal Realtime messages and the Data Request (RQ1) messages and
the Data Set (DT1) messages will be set automatically.
3rd byte
00H
3rd byte
mmH
3rd byte
00H
status
F7H
G Universal Non-realtime System Exclusive
Messages
❍Identity Request Message
When this message is received, Identity Reply message (p. 73) will be transmitted.
status
data byte
F0H
7EH, dev, 06H, 01H
Byte
Remarks
F0H
Exclusive status
7EH
ID number
dev
device ID
06H
sub ID#1
01H
sub ID#2
F7H
EOX
* The "dev" is own device number or 7FH (Broadcast).
❍GM System On
"GM System On" is a command message that resets the internal settings of the instrument
to the GM initial state (General MIDI System - Level 1). A GM instrument that receives this
message will automatically enter a state in which it can correctly perform a GM score.
status
data byte
F0H
7EH, 7FH, 09H, 01H
Byte
Remarks
F0H
Exclusive status
7EH
ID number
7FH
device ID
09H
sub ID#1
01H
sub ID#2
F7H
EOX
❍GM System Off
When this messages is received, this instrument will return to the performance mode.
status
data byte
F0H
7EH, 7FH, 09H, 02H
Byte
Remarks
F0H
Exclusive status
7EH
ID number
7FH
device ID
09H
sub ID#1
02H
sub ID#2
F7H
EOX
G Universal Realtime System Exclusive
Messages
❍Master Volume
status
data byte
F0H
7FH, 7FH, 04H, 01H, llH, mmH
Byte
Remarks
F0H
Exclusive status
7FH
ID number
7FH
device ID
04H
sub ID#1
01H
sub ID#2
llH
LSB of Master Volume
mmH
MSB of Master Volume
F7H
EOX
* LSB of Master Volume (llH) is processed as 00H.
* This message is not received in GM mode.
Aplicación MIDI
status
F7H
(Universal Non-realtime message)
(dev: 10H)
(General Information)
(Identity Request)
(End Of Exclusive)
status
F7H
(Universal Non-realtime message)
(Broadcast)
(General MIDI Message)
(General MIDI On)
(End Of Exclusive)
status
F7H
(Universal Non-realtime message)
(Broadcast)
(General MIDI Message)
(General MIDI Off)
(End Of Exclusive)
status
F7H
(Universal Realtime message)
(Broadcast)
(Device Control Message)
(Master Volume)
(End Of Exclusive)
71