Descargar Imprimir esta página

Aiwa AV-DV70 Manual De Instrucciones página 7

Publicidad

Idiomas disponibles

Idiomas disponibles

USINGI WITH TV
When
you operate
the receiver,
you can check
the receiver
settings
on the TV screen,
if the connected
TV is turned
on (On
Screen Display function).
The following
screen shows the sound
effect settings
of the Dolby Digital Surround.
For the further
details,
see "ON SCREEN
DISPLAY"
on page
DOLBY DGTL SU~N NORMAL
SUBW
L
LVL
MAX
CEN LVL
OdE
MAX
~R
~!k
OdB
SL
LVL
OdB
CEN DELAY
Orns
SUR DELAY
5ms
LFE
LVL
OdB
MIDNIGHT
STD
The TV screen
turns to blue if the TV signal
or video
signal
sent from the VCR/camcorder
is weak or unlocked
to the sync
signal. The screen restores the proper indication
when the TV/
video signal turns to good condition.
The video recording
(connected
to the VIDEO
OUT jack of the
unit) is not affected
by the screen indication,
even if the screen
has changed
to blue.
AB3UTTHE
REMOTE CONTROL
Inserting batteries
Detach the battery
cover on the rear of the remote
control
and
insert two R6 (size AA) batteries.
R6(AA)
When to replace the batteries
The maximum
operational
distance
between
the remote control
and the sensor
on the unit should
be approximately
5 meters
(16 feet). When this distance
decreases,
replace
the batteries
with new ones.
Using the remote control
The instructions
in this manual
refer mainly to the buttons on the
main unit. Buttons
on the remote
control
with the same names
as those on the main unit can be used as well.
c If the unit is not going to be used for an extended
period
of
time,
remove
the batteries
to prevent
possible
electrolyte
leakage.
The remote control
may not operate
correctly
when:
- The line of sight between
the remote control
and the remote
sensor in the display window
is exposed
to intense light, such
as direct sunlight.
- Other remote controls
are used nearby (those of a television,
etc.)
Remote control operation
This remote control system allows you to operate
other external
equipment
besides
the AIWA receiver.
For details of the rennote
control
operation
for other external
equipment,
see "REMOTE
CONTROL"
on page 18.
The following
is an explanation
on how to operate
the Aiwa
receiver.
C=l
1
2
RECEIVER/DIGIT
AIWA
RECEIVER —
SET UP
MUTE —
POWER —
TUNER PRESET/
SURROUND
'uNcT'ON-evOLuM
Press the AIWA RECEIVER
button
ta
set
the
remote
controll
to the
Aiwa
receiver
mode.
Press one of the buttons indicated above.
FUNCTION
button
Each time this button
is pressed,
the sound
source
changes
FM (or AM)')
+V3+V2+V1+CD+AUX+
PHOIVO
cyclically.
a): The band, which you have tuned to for the last time, cotmes on.
TUNER
PRESET/S~JRROUND
buttons
Tune in the station which has been preset on the receiver.
To go to a higher
preset number,
press the UP~
button. To
go to a lower preset number,
press the DOWN 1+1 button.
This
button
is also
used when
adjusting
the speaker
level
balance
of the DSP, Dolby Pro Logic or Dolby Digital Surround
mode.
It is not necessary
to press the AIWA RECEIVER
button each
time you operate
the Aiwa receiver
unless
another
mode
has
already
been set. (See "REMOTE
CONTROL"
on page 18.)
If the receiver cannot be operated with the remote
control
Follow the steps below using the remote control.
1
2
3
Press the AIWA RECEIVER
button.
Press and hold the SET UP button for -about 2.5
seconds.
The indicator
on the top of the remote
control
blinks twice
while pressing
this button.
Press the DIGIT buttons in the order of "4;' "O"
and "6."
ENGLISH
6

Publicidad

loading