Adjusting The Number Of Dmx Channels; Adjusting The Start Address; Display Of The Firmware Version; Cleaning The Unit - IMG STAGELINE PARL-42SET Manual De Instrucciones

7.2 Adjusting the number of DMX channels

The number of DMX channels depends on the
functions required and possibly also on the number
of control channels available on the light controller.
In the 14-channel mode the four spotlights can sep-
arately be controlled for colour mixing, while in the
5-channel mode only a common control is possible.
To select the number of DMX channels:
1) Press the button MENU / ESC repeatedly until
the main menu is reached.
2) Select the option
button UP or DOWN.
3) Press the button ENTER: the channel mode
presently adjusted is displayed:
= 5-channel mode
= 14-channel mode
4) Select the desired option with the button UP or
DOWN.

7.3 Adjusting the start address

For controlling the spotlights adjust a DMX start
address for its first DMX channel. The following
DMX channels are then automatically assigned to
the following addresses.
Example: For start address 5 for channel 1
– in the 5-channel mode, the channels 2 to 5 are
assigned to the addresses 6 to 9. The address 10 is
the next possible free start address for the following
DMX-controlled unit.
– in the 14-channel mode, the channels 2 to 14 are
assigned to the addresses 6 to 18. The address 19 is
the next possible free start address for the following
DMX-controlled unit.
1) Press the button MENU / ESC repeatedly until
the main menu is reached.
2) Select the option
button UP or DOWN.
3) Press the button ENTER: The present address
adjusted, e. g.
4) Adjust the desired address with the button UP or
DOWN.
After adjusting the start address the spotlights can
be operated via the DMX controller. The reception
of control signals will be indicated by a point flash-
ing on the display.
in the main menu with the
in the main menu with the
, is displayed.
8

Display of the Firmware Version

To indicate the version number of the firmware
(operating system of the unit):
1) Press the button MENU / ESC repeatedly until
the main menu is reached.
2) Select the option
button UP or DOWN.
3) Press the button ENTER: The display shows the
present version number (e. g.
9

Cleaning the Unit

The plastic panes in front of the LEDs should be
cleaned at regular intervals, depending on impuri-
ties caused by dust, smoke or other dirt particles.
Only this will ensure that the light is radiated at
maximum brightness. Prior to cleaning, discon-
nect the mains plug from the socket. Only use a
soft, clean cloth and a mild detergent. Then wipe
the plastic panes dry.
For cleaning the other parts of the housing only
use a dry, soft cloth. Never use chemicals or any
fluid; it may leak into the unit and cause damage.

10 Specifications

Power supply: . . . . . . 230 V~ / 50 Hz
Power consumption
PARL-42SET: . . . . . 80 VA max.
PARL-47SET: . . . . . 165 VA max.
Light source
PARL-42SET: . . . . .4 × 144 super bright 10 mm
PARL-47SET: . . . . . 4 × 7 super bright 3 W
Ambient temperature: 0 – 40 °C
Dimensions: . . . . . . . . 1210 × 345 × 80 mm
Height of stand: . . . . . 1.5 to 3.2 m
Weight
PARL-42SET: . . . . . 19.4 kg
PARL-47SET: . . . . . 20.5 kg
Subject to technical modification.
in the main menu with the
).
LEDs, 48 in red, green
and blue respectively,
beam angle 20°
RGB LEDs,
beam angle 25°
(controller with spotlights)
GB
17