Assembly And Adjustments; Intended Use - Black and Decker BEMW472ES Manual De Instrucciones

• An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety. The smaller
the gauge number of the wire, the greater the capacity
of the cable, that is, 16 gauge has more capacity than 18
gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using
more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V 25 (7.6)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More not
American Wire gauge
Than More
Than
0 6 18
6 10 18
10 12 16
12 16 14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

This mower is designed for residential lawn
mowing applications.
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
16 16 14
16 14 12
16 14 12
12 Not Recommended
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
See Fig. A to familiarize yourself with
the location of various controls and
adjustments. Save this manual for
future reference.

WARNING: Before assembly, make sure the ON/
OFF switches are released.
Assembling the grass catcher
(Fig. B, B1, B2, B3)

WARNING: Under normal usage, the collection
bag assembly is subject to deterioration and wear
and should, therefore, be frequently checked for
replacement. Any replacement assembly should
be checked for compliance with BLACK+DECKER
recommendations.
1. Before starting to assemble the grass bag to the frame,
check that the grass bag and frame are similar to Fig. B.
2. Slide the grass bag onto the frame as shown in Fig. B1.
3. Assemble the top clips to the frame as shown in
Fig. B2, then assemble the two side clips and the
bottom clip last.
4. Completely assembled grass catcher is shown in Fig. B3.
Fig. B
GRASSBAG
Fig. B1
English
FRAME
5