Sistema Del Menú - Yaesu FT-817ND Manual De Instrucciones

F
UNCIONAMIENTO DEL
del Menú
19 CW PADDLE
20 CW PITCH
21 CW SPEED
22 CW WEIGHT
23 DCS CODE
24 DIG DISP
25 DIG MIC
26 DIG MODE
27 DIG SHIFT
28 EMERGENCY
29 FM MIC
30 FM STEP
31 ID
32 LOCK MODE
33 MAIN STEP
34 MEM GROUP
35 MEM TAG
36 MIC KEY
37 MIC SCAN
38 OP FILTER
39 PKT MIC
40 PKT RATE
41 RESUME
42 RPT SHIFT
43 SCOPE
44 SIDETONE
45 SQL/RF-G
46 SSB MIC
47 SSB STEP
48 TONE FREQ
49 TOT TIME
50 VOX DELAY
51 VOX GAIN
52 EXTEND
53 DCS INV
54 R LSB CAR
55 R USB CAR
56 T LSB CAR
57 T USB CAR
1: Depends on transceiver version.
2: Depends on operating band and transceiver version.
FT-817 Manual de Instrucciones
ND
Función
Select the keyer paddle's wiring configuration
Setting of the pitch of the CW sidetone, BFO offset,
and CW filter center frequencies
Set the sending speed for the built-in Electronic keyer
Set the Dot:Dash ratio for the built-in electronic keyer
Setting the DCS code
Define the displayed frequency offset
during DIG (USER-L or USER-U) mode operation
Adjust the audio input level from terminal equipment
(such as a TNC or PSK-31 sound card)
during DIG (Digital) mode operation
Select the mode and sideband (if applicable)
in the DIG (Digital) mode
Define the carrier frequency offset
during DIG (USER-L or USER-U) mode operation
Enable Tx/Rx operation on the Alaska Emergency
Channel, 5167.5 kHz (USA Version only)
Adjust the microphone gain level for the FM mode
Select the tuning steps for the
on the FM mode
Store your callsign into the CW identifier
Select the operation of the front panel's
Setting of the 's tuning speed
Enable/disable the memory grouping feature
Store Alpha-Numeric "Tags" for the memory channels
Enable/disable CW keying
by the microphone's [ UP ] / [ DWN ] keys
Enable/disable scanning access
Enable the optional filter (CW or SSB) path
via the microphone's [ UP ] / [ DWN ] keys
Adjust the audio input level from the TNC
during 1200 bps Packet operation
Set the transceiver's circuitry for the Packet baud rate
Set the delay time for scanning resumption
Set the magnitude of the Repeater Shift
Select the Spectrum Scope mode
Adjust the CW sidetone volume level
Select the configuration of the front panel's
Adjust the microphone gain level for the SSB mode
Select the tuning steps for the
Setting the CTCSS Tone Frequency
Select the Time-Out-Timer time
Set the "hang time" for the VOX circuitry
Set the gain of the VOX circuitry's input audio detector
Enable/disable the extended Menu Items (#53 ~ #57)
Select "Normal" or "Inverted" DCS coding
Set the Rx Carrier Point for LSB
Set the Rx Carrier Point for USB
Set the Tx Carrier Point for LSB
Set the Tx Carrier Point for USB
S
ISTEMA DEL
Valores Disponibies Valor Original
NORMAL/REVERSE
300 ~ 1000 Hz
4wpm ~ 60 wpm/
20cpm ~ 300 cpm
1:2.5 ~ 1:4.5
104 Std DCS codes
-3000 ~ +3000 Hz
0 ~ 100
RTTY/
PSK31-L/PSK31-U/
USER-L/USER-U
-3000 ~ +3000 Hz
OFF/ON
0 ~ 100
knob 5/6.25/10/12.5/15/
–
key DIAL/FREQ/PANEL
FINE/COARSE
OFF/ON
OFF/ON
OFF/ON
OFF/SSB/CW
0 ~ 100
1200/9600 bps
OFF/3/5/10 seconds 5 sec
0 ~ 99.99 MHz
CONT/CHK
0 ~ 100
knob RF-GAIN/SQL
0 ~ 100
knob on the SSB mode 1/2.5/5 kHz
50 Std CTCSS tones 88.5 Hz
OFF/1 ~ 20 min
100 ~ 2500 msec
1 ~ 100
OFF/ON
Tn-Rn/Tn-Riv/
Tiv-Rn/Tiv-Riv
-300 ~ +300 Hz
-300 ~ +300 Hz
-300 ~ +300 Hz
-300 ~ +300 Hz
M
ENÚ
NORMAL
700 Hz
12 wpm
(60 cpm)
1:3.0
023
0 Hz
50
RTTY
0 Hz
OFF
50
2
20/25/50 kHz
YAESU
DIAL
FINE
OFF
– –
OFF
ON
OFF
50
1200 bps
2
CONT
50
1
50
2.5 kHz
OFF
500 msec
50
OFF
Tn-Rn
0 Hz
0 Hz
0 Hz
0 Hz
63