Key Dimensions And Specifications; Choose The Proper Location; Power Outlet; Flooring - Sears Kenmore Elite 796.2927 Serie Manual De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

I
I
KEY DiMENSiONS
AND SPECiFiCATiONS
Description
Top-Loading Washer
Rated Voltage/Frequency
120VAC, 60Hz
Dimensions
27"(W) X 283J8 '' (D) X 453J8 ' ' (H), 55_/_ '' (H with lid open)
68.6 cm (W) X 72.1 cm (D) X 115.3 cm (H), 141.7 cm (H with lid open)
Net Weight
145.5 Ibs. (66 kg)
CHOOSE
THE PROPER LOCATION
WARNING
. The washer is heavy! Two or more people are
required when moving and unpacking
the washer.
Failure to do so may result in damage to property or
serious bodily harm.
• Store and install the washer where it will not be
exposed to temperatures
below freezing or exposed
to outdoor
weather conditions.
Failure to follow this
warning can cause serious injury, fire, electrical shock, or
death.
• Properly ground washer to conform
with all govern=
ing codes and ordinances. Failure to follow this warning
can cause serious injury, fire, electrical shock, or death.
. To reduce the risk of electric
shock, do not install the
washer in humid spaces. Failure to follow this warning
can cause serious injury, fire, electrical shock, or death.
. The base opening must not be obstructed by carpeting
when the washer is installed on a carpeted floor.
. Keep the area underneath and around your appliances
free of combustible materials such as lint, paper, rags,
chemicals, etc.
• Do not remove ground prong. Do not use an adapter
or extension
cord. Plug into a grounded
3=prong out=
let. Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
Power Outlet
. The power outlet must be within 60 in. (1.5 m) of
either side of the washer.
. The appliance and outlet must be positioned so that
the plug is easily accessible.
. Do not overload the outlet with more than one
appliance.
• The outlet must be grounded in accordance with
current wiring codes and regulations.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation
of the product owner to have a proper outlet installed
by a qualified service person.
FLOORING
• To minimize noise and vibration, the washer MUST be
installed on a solidly constructed floor. See the NOTE.
• Allowable slope under the entire washer is a maximum 1"
difference from side to side or from front to back.
Carpeting and soft tile surfaces are not recommended.
Never install the washer on a platform or weakly
supported structure.
NOTE: The washer must be installed on firm flooring to
minimize vibration during the spin cycle. Concrete flooring
is best, but a wood floor is sufficient, provided it is built to
FHA standards. The washer should not be installed on
rugs or exposed to weather.
_
CLEARANCES
453/8"
(115.3 cm)
,,11
27"
1
._1"
(2.5cm_I_( 68.6cm)_
(2.5cm)
To ensure sufficient clearance for water lines and airflow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, lid, or floor moldings that may increase the
required clearances.
55.3/4"
(141.7 cm)
(with lid
open)
28.3/8'
_
4#
_(72.1
cm) _'"
1(10 crn)
Minimum vertical space from floor to overhead shelves,
cabinets, ceilings, etc., is 56".
I
I

Publicidad

Tabla de contenido
loading

Tabla de contenido