Safety Instructions For Batteries; Technical Data - REMS Nano Instrucciones De Servicio

eng
● Check the power cable, extension leads of the power tool and the power
supply regularly for damage. Have these renewed by qualifi ed experts or an
authorised REMS customer service workshop in case of damage.
● Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².

Safety instructions for Batteries

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
● Only use the battery in the REMS power tool. Only then is the battery safe
from dangerous overloading.
● Only use original REMS batteries with the voltage specifi ed on the rating plate.
Using other batteries can lead to injuries and risk of fi re due to exploding batteries.
● Use the battery and the rapid charger only in the specifi ed operating
temperature range.
● Only recharge REMS batteries in the REMS rapid charger. There is a risk of
fi re if an unsuitable battery charger is used.
● Charge the battery to full capacity with the rapid charger before using for
the fi rst time. Batteries are delivered partly charged.
● Never charge batteries unattended. Battery chargers and batteries can cause
hazards which lead to material damage and/or injury when charged unattended.
● Insert the battery into the battery compartment straight and without force.
There is a risk of bending the battery contacts and damaging the battery.
● Protect the batteries against heat, sunlight, fi re, moisture and wet. There is
a risk of explosion and fi re.
● Do not use the batteries in areas where there is a risk of explosion and in
the vicinity of infl ammable gases, solvents, dust, fumes, liquids for example.
There is a risk of explosion and fi re.
● Do not open the battery or modify its construction. There is a risk of explosion
and fi re due to short-circuiting.
● Do not use batteries with damaged housings or damaged contacts. Damage
to or improper use of the battery can cause fumes to escape. The fumes can irritate
the respiratory tracts. Let in fresh air and consult a doctor in case of symptoms.
● Fluid can leak from the battery when used improperly. Do not touch the
fl uid. Leaking fl uid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the fl uid gets into the eyes.
● Observe the safety instructions on the battery and the rapid charger.
● Keep unused batteries away from paper clips, coins, keys, nails, screws
or other small metal objects which could cause bridging of the contacts.
There is a risk of explosion and fi re due to short-circuiting.
● Remove the battery before stowing/storing the power tool for long periods
of time. Protect the battery contacts against short-circuiting, e.g. with a cap.
● Do not throw defective batteries in the normal household waste. Hand the defec-
tive batteries over to an authorised REMS contract service workshop or a recognised
disposal company. Observe the national regulations. See also page 6. Disposal.
● Keep batteries out of reach of children. Batteries can be life threatening if
swallowed, seek medical assistance immediately.
● Avoid contact with leaking batteries. Leaking fl uid can cause skin irritation
and burns. Rinse off immediately with water in case of contact. Also consult a
doctor if the fl uid gets into the eyes.
● Take the batteries out of the power tool when they are empty. This reduces
the risk of fl uids escaping from the batteries.
● Never recharge the non-rechargeable batteries, open them, throw them on
fi res or create a short-circuit. The batteries can cause fi res and burst. There
is a risk of injury. is a risk of injury. is a risk of injury
Explanation of symbols
WARNING
Danger with a medium degree of risk which could result in death
or severe injury (irreversible) if not heeded.
CAUTION CAUTION
Danger with a low degree of risk which could result in minor injury
(reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating instructions before use
REMS Nano complies with protection class I
REMS Akku-Nano and rapid charger comply
with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il
Environmentally friendly disposal
CE conformity mark

1. Technical Data

Use for the intended purpose
WARNING
REMS Nano and REMS Akku-Nano are intended for the purpose of cutting pipes.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
REMS Nano: Electric pipe cutting machine (without cutting wheel),
single open-ended wrench size 8, operating instructions,
carrying case.
REMS Akku-Nano: Cordless pipe cutting machine (without cutting wheel),
Li-Ion battery, Li-Ion/Ni-Cd rapid charger, single
open-ended wrench size 8, operating instructions,
carrying case.
1.2. Article numbers
REMS Nano
REMS Akku-Nano
REMS High-Power-Battery Li-Ion 10.8 V, 1.3 Ah
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
REMS cutting wheel Cu-INOX
REMS cutting wheel V
REMS Herkules 3B
REMS Herkules Y
REMS Jumbo
REMS Jumbo E
Carrying case
REMS CleanM
1.3. Application Area
REMS Nano, REMS Akku-Nano:
Pipes of pressfi tting systems made of
● stainless steel, C-steel (not jacketed)
● semi-hard and hard copper
● composite pipes
Operating temperature range
REMS Nano, REMS Akku-Nano
Battery
Rapid charger
1.4. Speed
REMS Nano, REMS Akku-Nano:
Idle speed of cutting wheel
1.5. Electrical Data
REMS Nano:
230 V~; 50 – 60 Hz; 130 W
Fuse (mains) 10 A (B), cut-out operation S3 20 % AB 2/10 min,
radio interference suppressed, protection class I, PE conductor as of
machine no. 3650
REMS Akku-Nano: 10,8 V – ---, 16 A, 270 W – ---, 16 A, 270 W –
Rapid-charger
Li-Ion/Ni-Cd Input 230 V~; 50 – 60 Hz; 65 W, all-insulated,
interference-suppressed
Output 10,8 – 18 V – ---
Input 100 – 120 V~; 50 – 60 Hz; 65 W, all-insulated,
interference-suppressed
Output 10,8 – 18 V – ---
1.6. Dimensions
REMS Nano:
L × W × H:
REMS Akku-Nano:
L × W × H:
1.7. Weights
REMS Nano
REMS Akku-Nano drive machine without battery
1.8. Noise Data
Workplace-related emission
value L = 78 dB L = 78 dB L
wA wA wA
1.9. Vibrations
Weighted effective value of the acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
CAUTION CAUTION
The indicated weighted effective value of acceleration can differ during operation
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual conditions of use (periodic duty) it may be necessary
to establish safety precautions for the protection of the operator.
eng
844000
844001
844510
571560
844050
844051
120120
120130
120200
120240
574436
140119
Ø 12 – 28 mm
Ø 10 – 35 mm
Ø 10 – 40 mm
–10 °C – +60 °C (14 °F – +140 °F)
–10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +113 °F)
130 min‫¹־‬
405 × 90 × 103 mm (15.9"× 3.5"× 4")
408 × 88 × 105 mm (16"× 3.4"× 4.1")
1.9 kg (4.2 lb)
2.0 kg (4.4 lb)
= 67 dB L = 67 dB L = 87 dB K = 3 dB
pA pA pA pC, peak
1.2 m/s² K = 1.5 m/s²
9