Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions & Parts Manual
Installation
(Continued)
DEEP WELL PUMP WITH PRE-CHARGED
STORAGE TANK (FIGURE 8)
1. Check tank pre-charge using a tire
pressure gauge. Set air pressure in
tank to 28 psi which is 2 psi below
pressure switch cut-in level. An air
valve is located on the side and
will accept a standard fitting from a
Prime
To Suction
Plug
Pressure
Switch
To Drive
Outlet
Figure 6 - Horizontal Tank
Air Volume Control
Hose
Outlet
Coupling
Prime To Suction
To Drive
Figure 7 - Vertical Tank
bicycle pump or air line.
2. Check the pressure with the power
off, faucets open and no water flowing
(zero water pressure).
3. Install a valve and isolator hose between
the system and the house plumbing to
aid in pump removal for servicing and for
reducing noise transmitted to the house
through the piping.
4. Provide a hose bib (faucet) at the
lowest point in the system to drain for
service or storage.
CONVERTING THE DEEP WELL PUMP
TO SHALLOW WELL OPERATION
(FIGURE 9)
For shallow wells (25 feet or less), a
bolt-on shallow well jet is available as an
accessory for deep well pumps. The jet
attaches to the front of the pump with the
two bolts provided and converts the deep
well pump into a shallow well pump. The
shallow well jet has a 1 in. NPT inlet and
Pressure
Switch
To Jet
Figure 8 - Pre-charged Storage Tank
Air
a 1/8 in. NPT opening for an air volume
Volume
control. For optimum performance, an
Control
incline check valve on the inlet side of the
Tubing
shallow well jet is recommended.
Electrical
Air
Volume
Control
designed for indoor installation only.
Select the proper size wire and
Air Volume
fuse (Chart 3). Time delay fuses are
Control Tubing
recommended over standard fuses
for motor circuit protection. All pump
To
Suction
Figure 9 - Shallow Well Jet
To Jet
motors have built-in automatic overload
protection that will prevent damage to the
motor due to overheating.
unit is permanently grounded. Connect ground wire
to approved ground then connect terminal provided.
A metal underground water pipe or well
casing at least 10 feet long makes the
best ground electrode. If plastic pipe
or insulated fittings are used, run a wire
CHART 3 - RECOMMENDED FUSE AND WIRING DATA - 60 HZ MOTORS
HP
Volt
115
1/2
230
115
1
230
Prime
Outlet
Plug
To
Suction
To Jet
To Drive
28-30 psi
1 HP
Risk of electrical
shock. This pump is
To Air Volume
Control
Jet
Do not connect to
electric power supply until
0
Dual
to
Element
50
Fuse
250V
15
14
10
14
20
12
10
14
5
50CJW and 100CJW
directly to the metal well casing or use a
ground electrode furnished by the power
company.
There is only one proper ground terminal
on the unit. The terminal(s) is located
under the pressure switch cover, is
painted green and is identified as GRD.
The ground connection must be made at
this terminal (Figure 10).
The ground conductor must not be
smaller than the circuit conductors
supplying the motor.
Check selector to voltage supply. They
must match change if needed.
The voltage of power supply must match
the voltage of the pump. The unit has dual
voltage motors preset at the factory to
115 volts. The motors can be converted to
230 volts by turning the voltage selector
to the desired voltage (see Figure 11).
Use needle nose pliers to pull the selector
out approximately 1/4 in., rotate and then
reinsert in correct position.
Disconnect power
and release all pressure
from the system before attempting to install,
service, relocate or perform any maintenance.
Operation
Ground
Screw
Line
Figure 10 - Electrical Connections
PRIMING THE SHALLOW WELL
Distance in Feet
From Meter to Motor
51
101
to
to
100
200
Wire Size
14
12
14
14
12
10
14
14
www.blueangelpumps.com
Motor
201
to
300
10
14
8
14
Publicidad
