Roland VR-760 Manual Del Usuario página 104

MIDI Implementado
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number:
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then Data Entry (Controller numbers
6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry
messages that is received at the same MIDI channel after that are recognized as changing
toward the value of the RPN messages. In order not to make any mistakes, transmitting
RPN Null is recommended after setting parameters you need.
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
00H, 01H mmH, llH
00H, 02H mmH, llH
7FH, 7FH ---, ---
Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number:
* Not received when the Rx PC Switch (Edit: System MIDI: Rx PC Switch) is OFF.
* Not received by the Organ Part.
Channel Pressure
Status 2nd byte
DnH vvH
n = MIDI channel number:
vv = Channel Pressure:
* The effect is vary depending on the tone.
* Not received by the Organ Part.
Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number:
mm, ll = Pitch Bend value:
104
3rd byte
mmH
llH
0H - FH (ch.1 - 16)
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
* Not received by the Organ Part.
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* Not received by the Organ Part.
RPN null
RPN and NRPN will be set as "unspecified."
Once this setting has been made, subsequent
Parameter values that were previously set will
not change.
mm, ll: ignored
0H - FH (ch.1 - 16)
00H - 3FH (prog.1 - prog.64)
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
Channel Mode Messages
All Sounds Off (Controller number 120)
Status 2nd byte
BnH 78H
n = MIDI channel number:
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
Reset All Controllers (Controller number 121)
Status 2nd byte
BnH 79H
n = MIDI channel number:
* When this message is received, the following controllers will be set to their reset values.
Controller Reset value
Pitch Bend Change +/-0 (center)
Channel Pressure 0 (off)
Modulation 0 (off)
Breath Type 0 (min)
Expression 127 (max)
Hold 1 0 (off)
Sostenuto 0 (off)
Soft 0 (off)
Hold 2 0 (off)
RPN unset; previously set data will not change
NRPN unset; previously set data will not change
All Notes Off (Controller number 123)
Status 2nd byte
BnH 7BH
n = MIDI channel number:
* When All Notes Off is received, all notes on the corresponding channel will be turned
off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.
OMNI OFF (Controller number 124)
Status 2nd byte
BnH 7CH
n = MIDI channel number:
* The same processing will be carried out as when All Notes Off is received.
OMNI ON (Controller number 125)
Status 2nd byte
BnH 7DH
n = MIDI channel number:
* The same processing will be carried out as when All Notes Off is received. OMNI ON
will not be turned on.
MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n = MIDI channel number:
mm = mono number:
* The same processing will be carried out as when All Notes Off is received.
POLY (Controller number 127)
Status 2nd byte
BnH 7FH
n = MIDI channel number:
* The same processing will be carried out as when All Notes Off is received.
3rd byte
00H
0H - FH (ch.1 - 16)
3rd byte
00H
0H - FH (ch.1 - 16)
3rd byte
00H
0H - FH (ch.1 - 16)
3rd byte
00H
0H - FH (ch.1 - 16)
3rd byte
00H
0H - FH (ch.1 - 16)
3rd byte
mmH
0H - FH (ch.1 - 16)
00H - 10H (0 - 16)
3rd byte
00H
0H - FH (ch.1 - 16)