Usage Instructions; Maintenance And Storage - Hudora Tour Instrucciones De Montaje Y De Uso

• Caution! Make sure that the quick-release fastener is released when you ad-
just the handlebar height or when you fully retract the handlebar to fold in the
scooter. Both securing buttons must be properly positioned and fixed before
fastening the quick-release fastener.
• Make sure that the handlebar locks into one of the provided handlebar
heights before you firmly tighten the quick-release fastener. The securing
buttons are fixed, when the handlebar is securely latched. Should they be
loose, the scooter must not be used!
ASSEMBLY INSTRUCTIONS
You do not need any tools for the assembly. The scooter will be delivered to you
in the transport state (folded up)! (Fig. 1)
In order to make the scooter ready for use, please proceed as follows:
• Place the scooter in front of you with the front wheel facing you. (Fig. 1) With
a little practice it is of course possible without having to put the scooter
down.
• Unfold the handles on both sides. (Fig. 2)
• Slightly raise the two parts of the handlebar base (1). (Fig. 3)
• Fold the two parts of the handlebar base (1) upwards together and align the
handles to the side so that the handlebars are centered on each other. (Fig. 4)
• By sliding the locking latch (2) from right to left, the safety bolt (3) springs
into the riding position and securely connects both handles. (Fig. 5)
• Make sure that the quick-release fastener (4) is released and grasp the
handlebar base with your left hand so that both securing buttons (5) are
pressed against the lower handlebar base and the securing bolts are as
such opened. You should thereafter, pull the handlebar upwards to the desi-
red height, with the right hand (fig. 6). Loosen the grip of your left hand and
release the securing button (5). Push down the handlebar until it locks into
place in one of the possible heights. Should it not be the desired height,
repeat this procedure.
• After you have set the desired height and the handlebars can no longer
be moved without actuating the securing buttons (5), please close the
quick-release fastener (4). (Fig. 7)
• Hold down the deck securing pin (6) and align the deck such that it is flat.
(Fig. 8)
• When the tour securing pin (7) has audibly locked into place, the scooter is
ready for use. (Fig. 9)
• Always check that all parts are firmly seated, in particular all the lock-in
securing devices, the axle bolts and the rollers.
To put the scooter back into the transport state, it is easiest to place it slightly
elevated (e.g. on a table or a step) transversely in front of you. With a little
practice, it is possible without having to put the scooter down. Please proceed
as follows:
• Press the deck securing pin (6) with the right hand to fold the deck and
press the two lugs of the tour securing pin (7) with your left hand to fold the
deck and handlebar together.
• Place the scooter in front of you, so that the front wheel points towards you.
• Press the safety bolt (3) in the handle bar and then slide the locking latch (2)
in the handle bar to the far right.
• Open the quick release fastener (4).
• Grasp the handlebar base with the right hand and press the securing button
(5) against the handlebar. Slide the handlebar all the way down up to the
stop.
• Fold both parts of the handlebars (1) to the left and right into a horizontal
line. Then fold up the handles, such that they engage on the inside of the
handlebar base (1). Lastly fold both parts of the handlebar base (1) down-
wards next to the front wheel.

USAGE INSTRUCTIONS

NOTHING'S EASY AT FIRST ...
... most accidents happen to "beginners" within the first ten minutes. Particular
care should be taken during this stage.
USAGE INSTRUCTIONS
The scooter moves when a foot is used to regularly push off, just as with well-
known children's scooters. Braking is no problem either - simply step on the
friction brake over the back wheel (mudguard).
We recommend folding the scooter by hand after each use. Aluminium is a
good and light material but should also be handled carefully as it is not as hard
as steel, for example.

MAINTENANCE AND STORAGE

Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and
after each use. Do not make any structural changes. For your own safety, plea-
se use original spare parts only. These can be sourced from HUDORA. If parts
become damaged or if sharp edges or corners should develop, the product may
not be used any more. If in any doubt, please contact our service team (http://
www.hudora.de/). Store the product in a safe place where it is protected from
the elements, cannot be damaged, and cannot injure anyone.
Replace damaged or worn assembly parts in order to ensure the safety of your
scooter.
WHEEL CHANGE
Replacement wheels are available as accessories from http://www.hudora.de/
and should be replaced when they get worn down. To change the wheels, loos-
en the axle fitting with two Allen keys and remove the wheels from the axle. A
screwdriver or Allen key can be used to push the bearings out of the wheel in
order to use them again in the new wheels. However, it is usually advisable to
change the bearings when the wheels are being changed. Put the bearings into
the new wheel with the spacer sleeve and mount them to the frame with the
axle screws. Make sure that the axle has been screwed on tightly before start-
ing again!
BEARINGS
Your kick scooter is equipped with precision ball bearings, which were filled
with grease under high pressure, during manufacture. For this reason, the roll-
ers of the kick scooter only run lightly and swiftly, while under load. Bearings
are maintenance-free, but also wear parts. Caution! Worn bearings make con-
spicuous audible noises and their function is constrained. In order to maintain
optimal riding pleasure and to ensure lasting safety, you should replace bear-
ings, as soon as they begin to exhibit signs of being worn. In the case of full
load, and daily use, we recommend the replacement of the rollers and bearings,
twice a year. Bearings are available as accessories under http://www.hudora.
de/.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection
point provided in your area. Local waste management companies will be able
to answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. You can find numerous information
on the product, replacement parts, solutions to problems and lost assembly
manuals at http://www.hudora.de/.
All images are examples of the design.
6/12