Descargar Imprimir esta página

coltene/whaledent BioSonic UC125H Manual De Usuario página 4

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 17
4
IV. Filling Instructions
1. Insure that the blue drain handle
(Fig. 2) is fully rotated clockwise to
the "Closed" position. Fill the unit to
the fill line indicator (Fig. 3).
2. Pour the required amount of
ultrasonic cleaning solution (either
BioSonic General Purpose, BioSonic
Germicidal Cleaner or BioSonic
Enzymatic Ultrasonic Cleaner) into
the tank.
3. Change the solution in the tank daily,
or sooner if it appears soiled or
discolored. When beakers are used,
change the solution in the beaker
after each use.
4. Drain unit by fully rotating the blue
drain handle counter-clockwise to the
"Open" position and allow solution to
empty into sink or waste system.
Rinse tank and fully rotate the blue
drain handle clockwise to the
"Closed" position.
NOTE: Never operate the unit without
solution. Operating a dry tank will void the
warranty. Do not place objects directly on
bottom of tank. Always use accessory
baskets, cassette racks or beakers.
V. Operation Instructions
ACTIVATING THE UC125H. This section
explains how to clean instruments with
your BioSonic UC125H.
1. Press the STOP/START key from the
default screen.
2. SELECT A LOAD. Three load icons
will appear representing instrument
baskets, beakers, and cassettes. To
cycle through these icons:
a. PRESS THE ENTER KEY.
Choose the appropriate icon for
your particular load (the selected
icon will flash).
b. USE THE ARROW KEYS to increase
or decrease the amount of cleaning
time between 5 and 60 minutes.
c. PRESS THE ENTER KEY to store
the newly programmed default times.
d. PRESS THE STOP/START KEY to
begin cleaning.
3. WAIT. The UC125H will begin the
cleaning process. The UC125H will
continue to clean as the timer counts
down the remaining minutes from the
user-selected cleaning time. Once the
timer reaches zero, "Cycle Complete"
will display on the LCD until any
button is pressed. The screen will
then return to the default screen.
NOTE: The cleaning cycle can be
stopped at any time by pressing the
STOP/START button. The unit will then
return to the user selected default value.
C-POWER: C-Power is an exclusive
feature of the UC125H that will
automatically adjust the power in the tank
based on the load requirements. This
function provides improved stability
against varying solutions, solution level
and instrument loads.
The BioSonic Ultrasonic cleaner should
always be covered when operating to trap
aerosols in the unit. The BioSonic
UC125H is equipped with a "hinged"
cover for easy one hand opening. The
cover also conveniently lifts off for
cleaning in spaces with low cabinets
above the unit.
VI. Heater Operation
Instructions
ACTIVATING THE HEAT FEATURE. The
UC125H model is equipped with a heater
to rapidly increase the temperature of the
solution in the tank.
NOTE: The temperature in the tank is
displayed in the lower right-hand corner of
the LCD screen.
1. PRESS THE HEAT KEY. Pressing
the HEAT key to activate this feature
will bring up a new screen on the
display. The first time this feature is
activated, the user must choose to
use Celsius or Fahrenheit. Using the
Arrow Keys, select "C" for Celsius or
"F" for Fahrenheit and press ENTER.
2. SET THE DESIRED
TEMPERATURE. Use the Arrow
Keys to increase or decrease
the tank temperature between
25°C (75°F) up to 60°C (140°F) in
5° degree increments. Press START
to accept this temperature. The unit
will now begin to heat.
BioSonic
3. WAIT. The UC125H will now display
the default screen and begin to heat
to the desired temperature. The Heat
Toggle will now display "ON." Once
the desired temperature is reached,
the Heat Toggle will display "OK."
Current temperature information will
always be displayed in the lower
right-hand corner of the LCD display.
CAUTION: The Heat feature of the
UC125H is a pre-heat temperature only.
Through prolonged use, the natural
cavitation process will continue to heat
the solution beyond the desired
temperature. When this happens, the unit
is still functioning properly.
NOTE: Once the unit is programmed to
use either Celsius or Fahrenheit, it will not
prompt you to do this again. If a mistake
is made or the user desires to change
from one to the other option, after
entering heat mode, press and hold the
HEAT key for three seconds and then
repeat steps 1 through 3.
VII. Solution Reset Operation
Instructions
USING THE SOLUTION TIMER. The
UC125H is equipped with a Solution
Reset button. This feature tracks the
amount of time your solution has been in
use. The solution life is displayed in hours
and minutes immediately above the
SOLUTION RESET key. To utilize
this feature:
1. PRESS THE SOLUTION RESET
KEY once after every change of your
ultrasonic cleaning solution. It is
recommended to change your
solution every 8 hours at a minimum,
or whenever the solution becomes
visibly cloudy or soiled.
Coltène/Whaledent offers a variety of
BioSonic ultrasonic cleaning solutions
to meet your cleaning needs.
2. VERIFY. The solution timer should
now display zeroes in the lower-left
corner of the LCD display.
VIII. Cleaning Methods
A. In Tank
Basket Cleaning: Place parts to be
cleaned into the basket (Fig. 5, 6, 7).
Then place the basket directly into the
main tank containing BioSonic
General Purpose, Germicidal, or
Enzymatic Cleaner. Clean according
to instructions on bottle cleaner label.
®
UC125H

Publicidad

loading