FLAEM Lella Manual De Instrucciones página 11

RHINO CLEAR® NASAL SHOWER
Before each use, wash your hands thoroughly and sanitize RHINO CLEAR® as described in section
"CLEANING, SANITIZATION, DISINFECTION AND STERILIZATION". During the application it is recommended
to be adequately protected against dripping.
1) Remove the adapter (C5.1) and the separator (C5.2).
2) Place the solution (max 10 ml) in the nebulizing chamber (C5.4.1) after having inserted the atomizer (C5.3).
3) Apply the separator (C5.2) verifying that the arrow on the shower body is aligned with the separator (Pic. B).
Then, insert the correct adapter for your age, or the most appropriate to fit the size of your nostrils (C5.1A/
C5.1B/C5.1C).
4) Connect the RHINO CLEAR® device through the tube (B) and the fitting (C6).
5) Turn on the device using the switch (A1).
6) Place the device close to the nose and gently insert the adapter nosepiece into one nostril.
7) During treatment it is preferable to hold the other nostril closed, where the shower is not applied, by applying
light finger pressure.
8) Run the shower holding down the manual dispensing button (C5.5) during the inhalation phase and release it
before exhaling; at this stage, to help expel the mucus, blow gently through the nostril treated directly into the
RHINO CLEAR®.
9) Repeat from Step 6 to Step 8 for the other nostril, trying to evenly distribute the solution between the two
nostrils.
10) When used on children or other dependent people, or in any case when there are problems in coordinating
the various phases of paragraph 8), we recommend to run the application alternating the nostrils about 20
seconds each, with pauses required to expel the mucus.
11) The operations described in the preceding paragraphs is useful for nasal cleaning using physiological solutions.
The treatment with drugs is advisable after a first cleaning with physiological solution in order to achieve a
more effective distribution of the drug on the nasal mucosa.
CLEANING, SANITIZATION, DISINFECTION AND STERILIZATION
Switch the device off and disconnect it from the power supply before proceeding with any cleaning operation.
CLEANING THE DEVICE AND THE TUBE'S OUTER SURFACE
Only use a cloth with antibacterial detergent (non-abrasive and with no solvents of any kind)
SANITIZATION, DISINFECTION AND STERILISATION OF THE ACCESSORIES
We recommend personal use of accessories to avoid any risk of spreading the infection.
Disassemble the accessories as described below:
C1 - Open the nebulizer by turning the upper part (C1.3) anticlockwise, remove the nozzle from the upper part
(C1.3) and then disassemble it as shown in the "Assembly diagram" in section C1.2.
C5 - Disassemble it as shown in the "Assembly diagram" in section C5.
SANITIZATION
Before and after each use, sanitise the accessories by choosing one of the methods described below
(method A): Sanitize the accessories C1.1-C1.2-C1.3-C1.4-C2-C3-C4-C5.1A-C5.1B-C5.1C-C5.2-C5.3-C5.4-C5.5.1-
C5.5.2-C6 using warm tap water (40°C approx.) with mild (nonabrasive) washing-up liquid or wash them in a
dishwasher, running a hot cycle.
(method B): Sanitize the accessories C1.1-C1.2-C1.3-C1.4-C2-C3-C4-C5.1A-C5.1B-C5.1C-C5.2-C5.3-C5.4-C5.5.1-
C5.5.2-C6 by soaking them in a solution of 50% water and 50% white vinegar. Rinse thoroughly with warm tap
water (40°C approx).
(method C): Sanitize the accessories C1.1-C1.2-C1.3-C1.4-C2-C5.1A-C5.1B-C5.1C-C5.2-C5.3-C5.4-C5.5.1-C5.5.2-C6
by boiling them in water for 20 minutes preferably using demineralised or distilled water to prevent limescale
deposits.
After sanitizing the accessories, shake them vigorously and lay them on a paper towel or dry them with a jet of
warm air (eg a hair dryer).
DISINFECTION
The accessories that can be disinfected are (C1.1-C1.2-C1.3-C1.4-C2-C3-C4-C5.1A-C5.1B-C5.1C-C5.2-C5.3-C5.4-
C5.5.1-C5.5.2-C6).
The disinfection procedure described in this paragraph is to be performed before using the accessories and is
effective only if all the prescriptions herein are met and all the components involved are previously sanitized.
The disinfectant to be used must be of electrolytic oxidizing chlorine type, (active ingredient: sodium hypochlorite),
specific for disinfection and is available in all pharmacies.
Procedure:
- Fill a container, suitable to contain all the individual components to be disinfected, with a solution of drinking
11