Models And Contents Of The Package - Dea ANGOLO 24/1 Instrucciones De Uso Y Advertencias

WARNING During motors stroke memorization, the control
board detects automatically the presence and type of photo-
cells, safety devices and limit switches which are installed. It is
therefore essential that during this phase the latter be properly
connected and working.
WARNING Wrong assessment of impact forces may cause
serious damage to people, animal and things. DEA System
reminds all personnel that the installer must ascertain that
these impact forces, measured according to EN 12445 pre-
scriptions, are actually below the limits indicated by EN12453
regulation.
WARNING Any external safety device installed in order to
conform to the limits set for impact forces must comply with
EN12978.
WARNING Dispose of batteries according to local regu-
lations in force (after they have been removed by qualified
personnel by cutting the fastening clamps).
WARNING In line with EU Directive 2002/96/EC for waste
electrical and electronic equipment (WEEE), this electrical pro-
duct must not be disposed of as unsorted municipal waste.
Please dispose of this product by returning it to your local
municipal collection point for recycling.
3 MODELS AND CONTENTS
OF THE PACKAGE
ANGOLO 24/1 is an electromechanical operator for swing
gates automation. It is essentially made up of:
-One gate operator
-One control board with built-in 433,92 MHz receiver, that
can be programmed thanks to 3 keys and one display (regula-
tion of force, speed, and motor stroke, etc.)
If you need to automate a two-leaf gate use ANGOLO 24/2
which includes a second motor without control board.ANGOLO
is available with 2 batteries to ensure use in case of power sup-
ply failure.
"AVAILABLE MODELS" table
Article
ANGOLO24/1 -No. 1 gate operator with control board
-No. 1 gate operator with control board
ANGOLO24/2
-No. 1 gate operator without control board
ANGOLO24/1/B -No. 1 gate operator with control board with batteries
-No. 1 gate operator with control board with batteries
ANGOLO24/2/B
-No. 1 gate operator without control board
"PRODUCT ACCESSORIES" Table
Article
Description
Codice
580V
580L
Aluminium articulated arm
580A
580B
Operating instructions and warnings
Description
Vertical
support
Horizontal
support
Rail arm
Inspect the "Contents of the Package" on Page 45 and com-
pare them with your product for useful reference during assembly.
4 OPERATING INSTRUCTIONS
I n co mplia nce w it h Direc t ive 2 00 6/42/ CE En c lo -
sure I , Point 1 .7 .4 .
4.1 Product description
ANGOLO is an electromechanical operator for swing gates.
It is made up of a mechanical gate operator (see F1, page 46)
which rotates an articulated or rail arm fastened to the leaf to
4.2 Technical data
"TECHNICAL DATA" table
Single-phase power supply volta-
ge (V)
Power supply voltage (V)
Absorber power (W)
Work cycle
Max torque (Nm)
No. of transmitters controlled
Operating temperature range (°C)
Opening time to 90° (s)
Degree of protection
Flashing light output
Auxiliary circuits power supply
output (+24VAUX)
Safety devices power supply ou-
tput (+24VSIC)
Electric lock output
LC/SCA contact capacity
F1 Fuse
F2 Fuse
Radio receiver frequency
Weight of product including
packaging (Kg)
Overall dimensions (mm)
automate.
4.3 Labelling information
Part of the summarised data concerning the CE label are
listed in the label applied to the product (see Position F4, Page
46); the data regarding the seller are found in the enclosed
Warranty, while "Indispensable Operating Safety Elements" are
found under Point "4.2 Technical data".
4.4 Appropriate conditions of use
ANGOLO is designed for installation on swing gates as
shown in F3 on Page 47.
ANGOLO has been designed and tested for operation under
"normal" gate opening conditions; temperature limits, degrees
of protection against dust and water, and other data are provi-
ded in Point 4.2 "Technical Data".
A N G O L O
230 V ~ ±10%
(50/60 Hz)
24 V
60 120
15s-1s-15s x10 times
2,5 min PAUSE
120
100
-20 ÷ 60
15
IP44
30V 10W max art.
Lumy 24S
24 V
max 200mA
24 V
max 200mA
max 1 Electric lock
art. 110
max 5A
T2A 250V (delayed)
T20A 250V (delayed)
433,92 MHz coding
rolling code / dipswitch
12,5 25
11
See F2, page 46,47