Sime BRAVA DGT HE 12 T Instrucciones De Instalación Y Mantenimiento página 107

3.2 ACCESS TO INSTALLER'S
PARAMETERS
For access to the installer's parameters,
press simultaneously the keys of boiler
panel ( and ) for 5 seconds.
The red LED flashes and the display shows:
The parameters can be scrolled with
or .
To enter the parameter press
The value set flashes, the display shows:
Proceed as follows to change the set value:
- set the new value using or
- confirm the set value using
Press to exit the parameters section.
The display is shown automatically after 5
minutes. The parameters section contains
the alarms log, info and meters (display
only).
3.2. 1 Replacing the board or
RESETTING parameters
If the electronic board is replaced or reset,
it is necessary to configure PAR 01 and
PAR 02 by associating the following values
to each type of boiler to be able to restart
the boiler:
GAS MODELS
25
METHANE 30
(G20) 35
12 T
25
PROPANE 30
(G31) 35
12 T
BOILER
25-30-35
25-30-35
combined with
sun-panel system
12 T with storage tank
12 T
NOTE: the boiler panel has a label with
the values that have to be set for PAR 01
and PAR 02 (fig. 19).
FAST CONFIGURATION
PAR DESCRIPTION
01 Combustion configuration
02 Hydraulic configuration
03 Disabling of voltage presence LED
04 Correction of external probe values
05 Timer block of the keys
09 Fan rpm Step ignition
or . D.H.W. - HEATING
PAR DESCRIPTION
10 Boiler antifreeze
11 External sensor antifreeze
12 Climatic curve setting
13 Minimum temperature heating
14 Maximum temperature heating
.
15 Maximum power heating
or .
16 Post-circulation time
17 Pump heating activation delay
18 Re-ignition delay
19 Flow meter modulation saturation band
29 Anti-legionella (only D.H.W. tank)
PARAMETERS RE-SET
PAR DESCRIPTION
49 * Reset default parameters
(PAR 01 - PAR 02 equal "---")
* If the current setting is difficult to understand or anomalous behaviour or if it is difficult to understand
the boiler, it is advised to restore the initial parameter values by setting PAR 49 = 1 and PAR 1 and
PAR 2 as specified in point 3.2.1.
ALARMS (visualization)
PAR DESCRIPTION
PAR 1
A0 Last code anomaly appearance
A1 Code anomaly previously appearance
A2 Code anomaly previously appearance
A3 Code anomaly previously appearance
01
A4 Code anomaly previously appearance
02
A5 Code anomaly previously appearance
03
A6 Code anomaly previously appearance
07
A7 Code anomaly previously appearance
A8 Code anomaly previously appearance
A9 Code anomaly previously appearance
04
05
INFO (visualization)
06
PAR DESCRIPTION
08
i0 External sensor temperature
i1 C.H. 1 sensor temperature
i2 C.H. 2 sensor temperature
PAR 2
i3 Fumes sensor temperature
i4 Auxiliary sensor AUX temperature
01
i5 Set of effective heating temperature
i6 Level ionization flame
i7 Number of fan revolutions
02
i8 Flow rate D.H.W. flow meter
COUNTERS (visualization)
03
PAR DESCRIPTION
c0 Number hours of operation of the burner
04
c1 Number of ignitions of the burner
c2 Number total of the anomalies
c3 Number approached the parameters installator
c4 Number approached the parameters OEM
PARAMETERS INSTALLER
RANGE
MEASUREMENT
-- = ND
1 ... 20
-- = ND
1 ... 14
0 = Disabled
1 = Enabled
-5 ... 05
-- = Disabled
1 ... 99
00 .... 81
RANGE
MEASUREMENT
0 ... 10
-- = Disabled
- 9 ... 05
03 ... 40
20 ... PAR 14
PAR 13 ... 80
30 ... 99
0 ... 99
0 ... 99
0 ... 10
0 ... 99
O = Disabled
1 = Enabled
RANGE
MEASUREMENT
-- , 1
RANGE
MEASUREMENT
=
=
=
=
=
=
=
=
=
=
RANGE
MEASUREMENT
-9 ... 99
-9 ... 99
-9 ... 99
-9 ... 99
-9 ... 99
PAR 13 ... PAR 14
00 ... 99
00 ... 99
00 ... 99
RANGE
MEASUREMENT
00 ... 99
00 ... 99
00 ... 99
00 ... 99
00 ... 99
UNIT OF INC/DEC DEFAULT
UNIT SETTING
= = "--"
= = "--"
= = 01
°C 1 00
Min. 1 15
rpm x 100 0, 1 from 0, 1 to 19,9 00
1 from 20 to 81
UNIT OF INC/DEC DEFAULT
UNIT SETTING
°C 1 03
°C 1 - 2
= 1 20
°C 1 20
°C 1 80
% 1 99
10 sec. 1 03
10 sec. 1 01
Min. 1 03
% 1 30
= = 0
UNIT OF INC/DEC DEFAULT
UNIT SETTING
= = =
UNIT OF INC/DEC DEFAULT
UNIT SETTING
= = =
= = =
= = =
= = =
= = =
= = =
= = =
= = =
= = =
= = =
UNIT OF INC/DEC DEFAULT
UNIT SETTING
°C 1 =
°C 1 =
°C 1 =
°C 1 =
°C 1 =
°C 1 =
% 1 =
100 rpm 1 =
l/min 1 =
UNIT OF INC/DEC DEFAULT
UNIT SETTING
h x 100 0, 1 from 0,0 to 9,9 00
1 from 10 to 99
x 1000 0, 1 from 0,0 to 9,9 00
1 from 10 to 99
x 1 1 00
x 1 1 00
x 1 1 00
IT
ES
PT
ENG
107